SEW-Eurodrive MOVI-C UHX45A Series Скачать руководство пользователя страница 57

Страница: 57 / 92

Startup with PROFINET IO

Configuration of the fieldbus stations

Manual – MOVI-C

CONTROLLER advanced with PROFINET IO Fieldbus Interface

5.4.1

Installing the device description file of the MOVI‑C

CONTROLLER

INFORMATION

A modified device description file can cause malfunctions in the device.

not

change or expand entries in the device description file. SEW‑EURODRIVE

assumes no liability for malfunctions of the device caused by a modified device de-
scription file.

A prerequisite for the correct configuration of the MOVI‑C

CONTROLLER with field-

bus interface PROFINET IO is the installation of the device description file (GSDML
file) in the TIA Portal. The file contains all relevant data for the engineering and data
exchange of the MOVI‑C

CONTROLLER.

The latest version of the device description file for the MOVI‑C

CONTROLLER with

fieldbus interface PROFINET IO is available on the SEW‑EURODRIVE website
→

www.sew-eurodrive.com

Search for "GSDML file for PROFINET IO" on the page

[Online Support] > [Data & documents] > [Software].

5.4.2

Creating a project in TIA Portal

Proceed as follows:

1. Start the TIA Portal.

2. Create a new TIA Portal project. Enter a project name and determine the storage

location of the project.

9007216444237067

24777730/EN – 01/2018

Содержание MOVI-C UHX45A Series





























































































Результаты поиска

Содержание MOVI-C UHX45A Series

Отзывы:

Бренды по названию

Популярные бренды

SEW-Eurodrive MOVI-C UHX45A Series, Руководство пользователя

Результаты поиска

Содержание MOVI-C UHX45A Series

Отзывы:

Бренды по названию

Популярные бренды