manualshive.com logo in svg

SEW-Eurodrive MOVI-C UHX45A Series, Руководство пользователя

Поделиться
Скачать
SEW-Eurodrive MOVI-C UHX45A Series Скачать руководство пользователя страница 13

3

Introduction

General information

Manual – MOVI-C

®

 CONTROLLER advanced with PROFINET IO Fieldbus Interface

13

3

Introduction

3.1

General information

3.1.1

Short designation

The following short designations are used in this documentation.

Type designation

Short designation

MOVI‑C

®

 CONTROLLER advanced UHX45A

MOVI-C

®

 CONTROLLER

Higher-level controller

PLC

3.1.2

Content of this manual

This manual describes:

•

The installation of the MOVI‑C

®

 CONTROLLER

•

The interfaces and LEDs of the MOVI-C

®

 CONTROLLER

•

The engineering access to the MOVI‑C

®

 CONTROLLER

•

Configuration and startup of the MOVI‑C

®

 CONTROLLER with the PROFINET IO

fieldbus interface

3.1.3

Additional documentation

To  be  able  to  configure  and  startup  the  MOVI‑C

®

  CONTROLLER  simply  and  effect-

ively, you should also order the following documentation in addition to this manual:

•

"Automation with MOVI-C

®

 CONTROLLER" manual

•

"MOVIDRIVE

®

 modular application inverter" product manual

•

"MOVIDRIVE

®

 system application inverter" product manual

Always use the latest edition of documentations and software.

The  SEW‑EURODRIVE  website  (www.sew‑eurodrive.com)  provides  a  wide  selection
of documents for download in various languages. If required, you can also order prin-
ted and bound copies of the documentation from SEW‑EURODRIVE.

24777730/EN – 01/2018

Содержание MOVI-C UHX45A Series





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды