SEW-Eurodrive MOVI-C UHX45A Series Скачать руководство пользователя страница 33

Страница: 33 / 92

Installation notes

Electrical installation

Manual – MOVI-C

CONTROLLER advanced with PROFINET IO Fieldbus Interface

No.

Designation

Ter-

minal

Function

[5] SD card slot

Card slot for SD memory card OMH45A (control
section with firmware, IEC program, user data)

INFORMATION:

Make sure the SD memory card

is correctly aligned when inserting it: The name-
plate must be on the right side of the SD memory
card.

[6] Reset button

Reset

[7] DIP switch

•

Bottom position:
Standard IP address of the X80 engineering
interface: 192.168.10.4 (cannot be changed)

•

Top position:
IP address on the SD memory card set by
user
(standard IP address of the X80 engineering
interface on delivery: 192.168.10.4)

[8] Fieldbus interface

(RJ45 socket)

X40/X41 •

MOVI‑C

CONTROLLER UHX45A-N:

Slave connection PROFINET IO

•

MOVI‑C

CONTROLLER UHX45A-E:

Slave connection EtherNet/IP™ or Mod-
bus TCP (in preparation)

[9] System bus and

RS485 interface
(9-pin connection)

X85

•

RS485 interface (in preparation)

•

System bus CAN 1 (in preparation)

•

System bus CAN 2 (in preparation)

24777730/EN – 01/2018

Содержание MOVI-C UHX45A Series





























































































Результаты поиска

Содержание MOVI-C UHX45A Series

Отзывы:

Бренды по названию

Популярные бренды

SEW-Eurodrive MOVI-C UHX45A Series, Руководство пользователя

Результаты поиска

Содержание MOVI-C UHX45A Series

Отзывы:

Бренды по названию

Популярные бренды