manualshive.com logo in svg

SEW-Eurodrive DH 21B Series, Руководство пользователя, Страница: 55 / 92

Поделиться
Скачать
SEW-Eurodrive DH 21B Series Скачать руководство пользователя страница 55

7

Project planning and startup with MOVITOOLS

®

 MotionStudio

Startup of the fieldbus at the DHR21B/41B controller

Manual – DHE/DHF/DHR21B (standard) and DHE/DHF/DHR41B (advanced)

55

Auto-crossing

The two ports leading out of the Ethernet switch have auto-crossing functionality. This
means that they can use both patch and cross-over cables to connect to the next Eth-
ernet node.

Auto-negotiation

The baud rate and duplex mode are negotiated by both Ethernet nodes when estab-
lishing  the  connection.  For  this  purpose,  both  Ethernet  ports  of  the  EtherNet/IP  con-
nection  support  an  auto-negotiation  functionality  and  work  with  a  baud  rate  of  either
100 Mbit or 10 Mbit in full duplex or half-duplex mode.

Notes on multi cast handling

•

The integrated Ethernet switch does not provide a filter function for Ethernet mul-
ticast telegrams. Multicast telegrams that are usually sent in Ethernet/IP networks
from the adapters to the scanners (PLC) are passed on to all switch ports.

•

IGMP snooping (e.g. Managed Switches) is not supported.

•

SEW‑EURODRIVE  therefore  recommends  to  connect  the  DHR21B/41B  option  in
EtherNet/IP networks only with network components that support IGMP snooping
(e.g. managed switch) or that have safety mechanisms integrated against excess
multicast  load  (e.g.  devices  from  SEW‑EURODRIVE).  Devices  that  do  not  have
this integrated function can fail due to high network loads. This restriction does not
apply to PROFINET IO or Modbus/TCP networks.

7.5.2

TCP/IP addressing and subnets

Introduction

The settings for the address of the IP protocol are made using the following paramet-
ers

•

MAC address

•

IP address

•

Subnet mask

•

Standard gateway

The addressing mechanisms and subdivision of the IP networks into subnetworks are
explained in this chapter to help you set the parameters correctly.

MAC address

The MAC address (Media Access Controller) is the basis for all address settings. The
MAC address of an Ethernet device is a worldwide unique 6-byte value (48 bits). The
MAC address of SEW Ethernet devices is 00-0F-69-xx-xx-xx. The MAC address is dif-
ficult  to  handle  for  large  networks.  This  is  why  freely  assignable  IP  addresses  are
used.

IP address

The IP address is a 32-bit value that uniquely identifies a node in the network. An IP
address is represented by 4 decimal numbers separated by decimal points.

Example: 192.168.10.4

22900055/EN – 08/2016

Содержание DH 21B Series





























































































Отзывы:

Нет отзывов