Servonaut ServoNaut Radio Zwo4 HS16 Скачать руководство пользователя страница 35

Страница: 35 / 58

Mixer function: All movements of controls
that affect this channel - no matter in which
direction - are added up.

See chapter Mixer

Functions

Test mode (yellow button): Yes

Attention

if you use the

test mode:

If the

maximum  is  set  to  +100%  the  controller
switches to full throttle with any key stroke.
If  you  need  to  teach  the  controller  in,  we
recommend  the  following  steps  in  test
mode:

Set [Off] to 0% and [Maximum] to +100%

set the controller in teach mode

according to its manual (often with a

jumper)

by pressing [Off] and [Maximum] you can

transmit the full deflection values to the

controller

press [Off] and then [Test] to leave the

test mode

at first reduce the [Maximum] to 50%

start the test mode again to adjust [Idle]

and [Maximum]. Be careful - the pump

starts!

Channel type [Pump –0->]

For

all

standard

ESCs

for

forwards/backwards that move a pump
in only one direction

. Full deflection on this

channel is -100% in one direction
and +100% in the other, center posi-
tion 0%. Only half the range is used

- from 0% to +100%. The instructions for
channel type [Pump-0–>] apply for this one
as well.

Typical use:

ESC for hydraulic pumps

; all

drives that run in one direction only.

Function: For a

pump the idle is adjust-

able

as well. After the pump lag time (see

[Pump lag] two pages before) the channel
activates the value set for [Off].

Emergency off: Channel activates the value
set for [Off]

Mixer function: All movements of controls
that affect this channel - no matter in which
direction - are added up.

See chapter Mixer

Functions

Test mode (yellow button): Yes
Hint: To test this controller/pump combina-
tion you can temporarily assign a joystick
control to a servo channel.

Menu Servo

Channel type [Cruise ctrl.]

Typical use:

Servonaut ESCs with cruise

control

e.g. M20+, K products

Function: For servonaut ESCs you can set

maximum speed

forwards and backwards,

brake force

and

neutral position

Emergency off: ESC brakes.

Mixer function: All controls that affect this
channel are added up.

Test mode (yellow button): No

Channel type 8 [Voith Schn.]

With this channel type you can get a ring
limiter e.g. for Voith Schneider Drives.

Be sure to check the manual of the Voith
Schneider Drive carefully.

Adjust the two channels for the servos that
steer the wings like this:

1. Channel type [Voith Schn.]

2. with the test mode adjust the servo

deflection so you get the maximum
travel left/right, forward/back and make
sure the middle position fits

3. change the direction of rotation if neces-

sarry

4. assign names to the channels e.g.

Forw/Back, L/R

Содержание ServoNaut Radio Zwo4 HS16



























































Результаты поиска

Содержание ServoNaut Radio Zwo4 HS16

Отзывы:

Servonaut ServoNaut Radio Zwo4 HS16, Руководство пользователя, Страница: 35 / 58

Результаты поиска

Содержание ServoNaut Radio Zwo4 HS16

Отзывы: