Sensorex TX2000 Скачать руководство пользователя страница 47

Страница: 47 / 50

8. Error messages (Error code)

Messages

Reason

Dispositions

Error1

Asy (Zero-point) exceeds

upper/lower limitation

Please use new buffers.

Clean the electrode or change

to a new electrode, and make

another calibration.

Error2

Slope exceeds upper/lower

limitation

Please use new buffers.

Clean the electrode or change

to a new electrode, and make

another calibration.

Error3

The readout is unstable

Check whether there is bubble or

air in the glass end of the

electrode

Clean the electrode or change

to a new electrode, and make

another calibration.

Error4

The temperature is over

the range 0~50

C during

calibration.

Buffer cannot be

recognized

Please adjust the standard

solution to the proper

temperature range.

Please check whether there is

bubble or air in the glass end of

the electrode

, or maintain the

electrode or change a new

electrode, and make another

calibration.

Error5

Wrong password

ERROR CODE

Re-enter a password

Error9

Serious error that does

not permit any further

measuring

Please contact Sensorex Technical

Support.

Содержание TX2000



















































Результаты поиска

Содержание TX2000

Отзывы:

Похожие инструкции для TX2000

Бренды по названию

Популярные бренды

Sensorex TX2000, Руководство по эксплуатации

Результаты поиска

Содержание TX2000

Отзывы:

Похожие инструкции для TX2000

Бренды по названию

Популярные бренды