Sensorex TX2000 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 50

background image

6.14 Backlight settings

Enter setup of backlight display. Set the brightness of display(-2~2, dark~bright) and
sensitivity of the sensitization sensor(-2~2, insensitive~sensitive). When a key is
pressed, the touch-on backlight function will be activated. Regardless of the type of
backlight mode, the touch-on function will activate the backlight. If there is no
keystroke for 5 seconds, the display will return to the original backlight setting status.

ON setting:

The backlight is always on.

OFF setting:

The backlight is off. When there is a keystroke, it enters to the touch-on status.

Auto setting:

According to the ambient light, activate or deactivate the backlight. When there is a

keystroke, it enters to the touch-on status.

Press or

to select

backlight mode.

Enter “Contrast” Setup

Press

or

to

select -2, -1, 0,

1, 2, five

backlight

brightness

levels

Press or

to select

backlight mode.

Press to confirm it.

Press to confirm it.

Press to confirm it.

Press to confirm it.

Press to confirm it.

Press to confirm it.

Press to confirm it.

Press

or

to

select -2, -1, 0,

1, 2, five

backlight

brightness

levels

Press

or

to select

-2, -1, 0, 1, 2, five

Backlit sensitization

levels.

«
...
33
34
35
36
37
...
»

Содержание TX2000



















































Отзывы:

Нет отзывов

Похожие инструкции для TX2000

Бренд: Nautel Страницы: 83

Бренд: Yaesu Страницы: 195

Бренд: Yaesu Страницы: 39

Бренд: Leuze electronic Страницы: 61

Бренд: MuxLab Страницы: 2

Бренд: WisyCom Страницы: 20

Бренд: T'nB Страницы: 24

Бренд: M-system Страницы: 3

Бренд: Trango Systems Страницы: 8

Бренд: Icom Страницы: 10

Бренд: RMG Страницы: 38

Бренд: CommRadio Страницы: 27

Бренд: Cirronet Страницы: 60

Бренд: M-system Страницы: 2

Бренд: Firstcom Страницы: 44

Бренд: CYP Страницы: 68

Бренд: ARG Страницы: 10

Бренд: Tapco Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды