manualshive.com logo in svg

Sensit GOLD G2, Инструкция по эксплуатации, Страница: 21 / 60

Поделиться
Скачать
Sensit GOLD G2 Скачать руководство пользователя страница 21

21

OPERATION AND USE

11.

 To disable the alarm, quickly press the POWER/MUTE BUTTON (A). 

To enable the alarm press the same button again. During an alarm the 

gas that has exceeded the preset alarm point will flash on the display and 

the HAZARD 3 LED will flash indicating a potentially unsafe condition.

When  combustible  gas  readings  exceed  the  alarm  range,  all  LEDs 

(except  green  and  red  HAZ3)  will  turn  off.  If  the  alarm  condition  no 

longer exists, the alarm sound will activate if a new alarm condition is 

encountered.

12.

 To assist in locating small leaks press and release the TICK/MENU 

BUTTON (B). The SELECT TEST TICK is displayed. Push the TICK/

MENU BUTTON (B) to activate the tick.

Upon activation a tick can be heard and a full bar graph is displayed. As 

the sensor head is moved toward a leak source the tick will increase. 

At any time press the TICK/MENU BUTTON (B) to reset the speed of 

the  tick  to  the  slow,  steady  rate. The  bar  graph  will  decrease  in  size 

indicating a decreasing range of tick rate sensitivity. Each bar division 

(there are 5) represents approximately 5000ppm methane.

MENU BUTTON (B) to reset the tick so that is audible. Pressing  the  

POWER/MUTE BUTTON (A)  disables the  tick 

NOTE:

  Whenever  possible  use  the  instrument  prior  to  using  a  leak 

detection solution.

Содержание GOLD G2





























































Отзывы:

Нет отзывов