manualshive.com logo in svg

senseFly EBEE RTK, Расширенное руководство пользователя

Поделиться
Скачать
senseFly EBEE RTK Скачать руководство пользователя страница 168

Maintenance, Repair and Troubleshooting

Airspeed
malfunction

The differential pressure sensor used to measure air-
speed is registering invalid values. This may be due
to a damaged sensor or to a clogged pitot probe.

Security action:

The drone flies towards the Home

waypoint at an altitude defined by the Home way-
point’s Change altitude parameter (by default, set to
‘Highest’) at a constant thrust value instead of con-
trolled speed, potentially resulting in low or high
flight speeds depending on wind. Once it reaches the
Home waypoint it initiates a landing procedure.

User action:

Try to provide a maximum amount of

approach sectors to ensure that the drone can land
against the direction of the wind. Land as soon as
possible and perform Check 4 in section ‘Full airframe
and sensor inspection’ on page 151.

Low airspeed

Detected airspeed is unusually low or close to zero.
This may be due to a collision with the ground or a
clogged airspeed sensor.

Security action:

The drone shuts off its motor and

tries to continue its mission.

User action:

If the warning is due to a clogged air-

speed sensor it may be due to moisture in the air.
Try commanding the drone to descend closer to the
ground and out of any cloud cover.

168

Содержание EBEE RTK































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды