manualshive.com logo in svg

senseFly EBEE RTK, Расширенное руководство пользователя

Поделиться
Скачать
senseFly EBEE RTK Скачать руководство пользователя страница 102

Advanced functionalities

Unexpected intrusions into airspace

Your drone is about to collide with another aircraft or UAV. Consider a fast climb
or descent.

Unexpected intrusions into landing zone

A person or vehicle moves into your landing zone during landing approach. Con-
sider aborting the landing.

Caution:

You cannot trigger an emergency manoeuvre if it will:

•

cause your drone to leave the working area.

•

make your drone fly below 30 m and cause a ground proximity
warning.

•

interrupt an emergency landing that was caused by a critical
failure.

Caution:

To avoid a collision, do not carry out a fast climb or fast

descent if this would risk flying close to trees or other obstacles.

Caution:

Some of these manoeuvres will cause a loss in altitude. To

avoid crashing your drone, do not carry out several emergency ma-
noeuvres in quick succession. Allow your drone to stabilise its flight
and altitude after each manoeuvre.

Caution:

While your drone is carrying out an emergency manoeu-

vre it cannot capture high-quality images and some images may be
missing at the end of the mission. In addition, these manoeuvres use
up battery power, shortening the available flight time. If, after acti-
vating a manoeuvre 3 times, the issue has not be resolved, consider
landing and waiting (for example, until birds have left the area) be-
fore restarting or resuming your mission.

102

Содержание EBEE RTK































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды