manualshive.com logo in svg

senseFly EBEE RTK, Расширенное руководство пользователя

Поделиться
Скачать
senseFly EBEE RTK Скачать руководство пользователя страница 145

Manual control of the

eBee RTK

left or right will set a left or right roll angle of up to 45

◦

/s, respectively. Moving

the stick down will set a climb rate of up to 3.5 m/s. Moving the stick up will set
a sink rate of up to 3.5 m/s. Releasing the right stick at any point will return the
drone to a straight flight path at a constant altitude.

It is not possible to take-off in Assisted Manual mode. You may only switch to
Assisted Manual mode after completing the standard take-off procedure⁴⁹.

Caution:

There is no clear indication during the take-off procedure

that the

eBee RTK

will change to Assisted Manual mode rather than

Circle Start Waypoint mode after the take-off transition altitude is
reached⁵⁰. For this reason we recommend that you do not turn on the
remote control unless you are ready to manually control the drone
right after take-off.

To perform a manual landing we recommend the following procedure:

1. The drone should always perform a linear landings into the wind. Face the

downwind direction and confirm that there are no obstacles in an area of at
least 100 m downwind and a width of 20 m in either direction from down-
wind.

2. Set the drone to an altitude of around 50 m from the landing altitude by

moving the right stick up or down.

3. Fly downwind until the drone is around 100 m away from the landing loca-

tion.

4. Turn the drone upwind and towards the landing location by moving the

right stick left or right.

5. Set the speed to a low value by moving the left stick down to around 25%

of its maximum value.

6. Bring the drone closer to the ground by controlling the sink rate with the

right stick. Keep the drone descending until it is around 5-10 m from the
ground.

⁴⁹ as described in section ‘Take-off’ on page 54

145

Содержание EBEE RTK































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды