background image

If a problem occurs ...

31

Specifications 

System

SR 300 IEM G3 transmitter

In compliance with

Approved by

Modulation

wideband FM stereo (MPX pilot tone)

Frequency ranges

516–558, 566–608, 626–668, 734–776, 780–822, 
823–865 MHz (A to E, G, see page 4)

Transmission/receiving frequencies

1680 frequencies, tuneable in steps of 25 kHz

20 frequency banks, each with up to 16 factory-preset channels

6 frequency banks with up to 16 user programmable channels

Switching bandwidth

42 MHz

Frequency stability

±10 ppm (–10°C to +55°C)

Compander system

Sennheiser 

HDX

Nominal/peak deviation

±24 kHz/±48 kHz

MPX pilot tone (frequency/deviation)

19 kHz/±5 kHz

AF frequency response

25 Hz to 15 kHz

THD (at 1 kHz and nominal deviation)

< 0.9%

Signal-to-noise ratio at nominal load and 
peak deviation

> 90 dB

Temperature range

–10°C to +55°C

Antenna output

BNC socket, 50 

Ω

 with remote power supply input 12 V DC

RF output power at 50 

Ω

typ. 10/30 mW (Low/Standard), switchable

AF input 

BAL AF IN L (I)/BAL AF IN R (II)

2 x XLR-3/¼’’ (6.3 mm) jack combo socket, 
electronically balanced

Max. input level

+22 dBu (line)

AF output 

LOOP OUT BAL L(I)/LOOP OUT BAL R(II)

¼’’ (6.3 mm) stereo jack socket, balanced

Headphone output

¼’’ (6.3 mm) stereo jack socket

Power supply

12 V 

Current consumption

max. 350 mA

Dimensions

approx. 202 mm x 212 mm x 43 mm

Weight

approx. 980 g

Europe

EMC

EN 301489-1/-9

Radio

EN 300422-1/-2

Safety

EN 60065

Canada

Industry Canada

RSS 123,

IC: 2099A-G3SREK

limited to 806 MHz

USA

FCC-Part 74  FCC-ID: DMOG3SREK

limited to 698 MHz

Содержание evolution wireless 300 IEM G3







































Отзывы: