manualshive.com logo in svg

SEMC TF20, Руководство пользователя, Страница: 17 / 30

Поделиться
Скачать
SEMC TF20 Скачать руководство пользователя страница 17

 

Last updated 10/29/2020 

16 

Make sure that the 626 holder has a good vacuum. Finally, send message in slack in 
#EMG channel: “Elsa is warming up now. V1 and V2 open, V3 and V4 of both Elsa and 
626 are closed. 626 has a good vacuum and should be ready to go first thing in the 
morning.” 

b.

 

You are done after this step. 

c.

 

If warming up the 626 holder, proceed to step 8. 

8.

 

Once warm up is done, close V1.

 

9.

 

Open V3, then open V4 of holder #1.

 

10.

 

Open V3, then open V4 of holder #2.

 

11.

 

On Fridays, start the “ZEOLITE CYCLE” for 2 hours.

 

 
 

***If for any reason you cannot finish warming up the 626 and/or Elsa holder and open V3 and V4 
to pump down the jacket of the holder by the end of your session, please send an email to 

[email protected]

 OR slack in #EMG channel:  

 
“626 and/or Elsa is still warming up right now. Only V1 and V2 are open, pumping down the tip 
only. Can someone from EMG please close V1 and then open V3 and V4 first thing in the morning 
to pump down the jacket of the holders?” 

 

 

Содержание TF20































Отзывы:

Нет отзывов