SelectBlinds Skylight Скачать руководство пользователя

Страница: 27 / 31

1. Select the channel that you want to

program using the

CHANNEL

selector

button.
2. Press the

SETTING

button on the

motor until the motor starts to beep.

Release the button immediately after the

beeps start. The motor will make 4 fast

beeps followed by 5 long beeps. Press the

CONFIRM

button on the remote anytime

during the series of long beeps. It must

be pressed before the last long beep. The

motor will respond with 3 fast beeps/jogs

confirming that the shade has been linked.

ADVANCED PROGRAMMING

REPLACE ORIGINAL REMOTE, ADD ADDITIONAL

REMOTE OR ADD SHADE TO AN ADDITIONAL CHANNEL

3. Repeat steps 1-2 to program the rest of the channels on a multi-channel

remote.
4. All shades linked to a remote will also automatically be programmed to the

“ALL” channel.

Setting

Button

On/Off

Switch

Up = On

Down = Off

CR2450

Channel

Display

Stop/Favorite

Down

Channel

Rail

Selector

Front

Confirm

Limit

Back (cover on)

Back (cover off)

Screw

Cover

slides

off

Содержание Skylight
































Результаты поиска

Содержание Skylight

Отзывы:

Похожие инструкции для Skylight

Бренды по названию

Популярные бренды

SelectBlinds Skylight, Инструкции по установке и уходу

Результаты поиска

Содержание Skylight

Отзывы:

Похожие инструкции для Skylight

Бренды по названию

Популярные бренды