SelectBlinds Skylight Скачать руководство пользователя

Страница: 25 / 31

FAVORITE POSITION

SETTING A FAVORITE POSITION

Use the

DOWN

buttons to position the shade at the desired “favorite”

position. While holding the

LIMIT

button, quickly press and hold the

button. Release both buttons when the shade makes a series of short beeps.

When complete, turn the other shades back on by setting the ON/OFF switch on

the motor to the “ON” position.

USING A FAVORITE POSITION

With the shade at either the upper or lower limit, simply press the

STOP/

FAVORITE

button to bring the shade to the “favorite” position. To go to the

“favorite” position from any other location, make sure the shade has been

stopped for at least three seconds before pressing the

STOP/FAVORITE

button.

If there is only a single shade on the channel proceed to setting favorites below.

If there is more than one shade on the channel, all other shades on that channel

will need to be disabled.

To disable a shade, set the ON/OFF switch on the motor to the “OFF” position.

CR2450

Channel

Display

Stop/Favorite

Down

Channel

Rail

Selector

Front

Confirm

Limit

Back (cover on)

Back (cover off)

Screw

Cover

slides

off

Содержание Skylight
































Результаты поиска

Содержание Skylight

Отзывы:

Похожие инструкции для Skylight

Бренды по названию

Популярные бренды

SelectBlinds Skylight, Инструкции по установке и уходу

Результаты поиска

Содержание Skylight

Отзывы:

Похожие инструкции для Skylight

Бренды по названию

Популярные бренды