background image

SEL- 2664S Data Sheet

Schweitzer Engineering Laboratories, Inc.

14

Optoisolated Control Inputs (Internally Wetted to 24 Vdc)

Current Draw at Nominal DC 

Voltage:

4 mA typical

Rated Insulation Voltage (U

i

):

300 Vac

Rated Impulse Withstand Voltage 

(U

imp

):

5000 V

Pickup/Dropout Time:

<20 ms

Time-Code Input

Format:

Demodulated IRIG-B

On (1) State: 
Off (0) State: 

Vih 



2.2 V

Vil 

 0.8 V

Input Impedance:

2 k

Synchronization Accuracy Internal 

Clock:

1 µs

All Reports:

5 ms

Simple Network Time Protocol 

(SNTP) Accuracy Internal 
Clock:

5 ms

Unsynchronized Clock Drift Relay 

Powered:

2 minutes per year, typically

Communications Ports

Standard EIA-232 (2 Ports)

Location:

Front Panel
Rear Panel

Data Speed:

300–38400 bps

Ethernet Port

Dual 100BASE-FX (LC connector)

Standard Multimode Fiber-Optic Serial Port

Location:

Rear Panel

Data Speed:

300–38400 bps

Fiber-Optic Ports Characteristics

Port 1 (or 1A, 1B) Ethernet

Wavelength:

1300 nm

Optical Connector Type:

LC

Fiber Type:

Multimode

Link Budget:

16.1 dB

Typical TX Power:

–15.7 dBm

RX Min. Sensitivity:

–31.8 dBm

Fiber Size:

62.5/125 µm

Approximate Range:

~6.4 km

Data Rate:

100 Mbps

Typical Fiber Attenuation:

–2 dB/km

Port 2 Serial

Wavelength:

820 nm

Optical Connector Type:

ST

Fiber Type:

Multimode

Link Budget:

8 dB

Typical TX Power:

–16 dBm

RX Min. Sensitivity:

–24 dBm

Fiber Size:

62.5/125 µm

Approximate Range:

~1 km

Data Rate:

5 Mbps

Typical Fiber Attenuation:

–4 dB/km

Communications Protocols

SEL, Modbus, DNP3, FTP, TCP/IP, Telnet, SNTP, IEC 61850, M

IRRORED

 

B

ITS

Operating Temperature

IEC Performance Rating 

(per IEC/EN 60068-2-1 
and 60068-2-2):

–40° to +85°C (–40° to +185°F)
Not applicable to UL applications

Operating Environment

Insulation Class:

1

Pollution Degree:

2

Overvoltage Category:

II

Atmospheric Pressure:

80–110 kPa

Relative Humidity:

5%–95%, noncondensing

Maximum Altitude Without 

Derating (Consult Factory for 
Higher Altitude Derating):

2000 m

Dimensions

Surface Mounting

Width:

26.12 cm (10.28 in) maximum

Depth:

13.21 cm (5.2 in) maximum 

(includes mounting brackets)

Height:

26.54 cm (10.45 in) maximum 

(includes mounting brackets)

Panel Mounting

Width:

19.12 cm (7.53 in) maximum

Depth:

26.11 cm (10.28 in) maximum

Height:

23.70 cm (9.33 in) maximum

Rack Mounting

Width:

48.26 cm (19 in) maximum

Depth:

26.11 cm (10.28 in) maximum

Height:

26.59 cm (10.47 in) maximum

Weight

Wall Mount: 
Panel Mount: 
Rack Mount: 

4.02 kg (8.87 lbs)
4.69 kg (10.33 lbs)
7.96 kg (17.55 lbs)

#6 Ground Screw and #6 Chassis Screw Tightening Torque

Minimum:
Maximum:

1.13 Nm (10 in-lb)
1.36 Nm (12 in-lb)

#8 Chassis and Wall Mount Bracket Screw Tightening Torque

Minimum
Maximum:

1.24 Nm (11 in-lb)
1.47 Nm (13 in-lb)

#6 Captive Screw in Front Bezel, Screw Tightening Torque for Panel/ 
Rack Mount Options

Minimum:
Maximum:

1.13 Nm (10 in-lb)
1.36 Nm (12 in-lb)

1/4-20 Hex Nut Tightening Torque for Panel/ Rack Mount Options

Minimum:
Maximum:

5.08 Nm (45 in-lb)
6.21 Nm (55 in-lb)

Terminal Connections for Terminal Blocks A, B, and C

Compression Plug Tightening Torque

Minimum:
Maximum: 

0.5 Nm (4.43 in-lb)
0.6 Nm (5.31 in-lb)

Compression Plug Mounting Ear Screw Tightening Torque

Minimum: 
Maximum:

0.2 Nm (1.77 in-lb)
0.3 Nm (2.65 in-lb)

Содержание SEL-2664S

















Отзывы: