Seitron CHEMIST 400 Скачать руководство пользователя страница 27

Страница: 27 / 89

K900000000SE 022628A0 071013

▲

Automatic analysis

Condensation

NOx/NO factor

Alarms

►Autozero/Pump

▼

CONFIGURATION

►Autozero

Pump

AUTOZERO/PUMP

Autozero

Pump

AUTOZERO/PUMP

Autozero

Pump

AUTOZERO/PUMP

Note:
The pump cannot be
switched  off  during
auto-calibration.
If auto-calibration has
not  been  performed
the  pump  cannot  be
switched on.

Autozero

►Pump

AUTOZERO/PUMP

Autozero

Pump

AUTOZERO/PUMP

Autozero

Pump

AUTOZERO/PUMP

off

Select the figure to be modified with the
keys           .
Modify  the  value  of  the  highlighted
figure with keys          .

The values that can be selected with the

keys for this parameter are:

The values that can be selected with the

keys for this parameter are:

maximum

minimum

▲

Reference

Automatic analysis

Condensation

NOx/NO factor

►Alarms

▼

CONFIGURATION

►Number

Measure

Active

Limit

Unit

ALARMS

maximum

1500

ppm

Number

Measure

Active

Limit

Unit

ALARMS

maximum

CO ev

2000

ppm

Number

Measure

Active

Limit

Unit

ALARMS

maximum

1500

ppm

Number

►Measure

Active

Limit

Unit

ALARMS

maximum

1500

ppm

Number

Measure

►Active

Limit

Unit

ALARMS

maximum

1500

ppm

Number

Measure

Active

Limit

Unit

ALARMS

minimum

1500

ppm

Number

Measure

Active

Limit

►Unit

ALARMS

maximum

1500

ppm

Number

Measure

Active

Limit

Unit

ALARMS

maximum

1500

ppm

Number

Measure

Active

►Limit

Unit

ALARMS

maximum

1500

ppm

Number

Measure

Active

Limit

Unit

ALARMS

maximum

+01500.0000

ppm

The  alarm  threshold  values  can  be  set
via  the          keys  within  the  following
range:

- 99999.999 to + 99999.99

(the value is referred to the unit of
measurement set) maximum, minimum, no.

The values that can be selected with the

keys for this parameter are:

ppm

mg/m

mg/kWh

g/GJ

g/m

g/kWh

Содержание CHEMIST 400


























































































Результаты поиска

Содержание CHEMIST 400

Отзывы:

Похожие инструкции для CHEMIST 400

Бренды по названию

Популярные бренды

Seitron CHEMIST 400, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание CHEMIST 400

Отзывы:

Похожие инструкции для CHEMIST 400

Бренды по названию

Популярные бренды