Seitron CHEMIST 400 Скачать руководство пользователя страница 21

Страница: 21 / 89

K900000000SE 022628A0 071013

▲

Sensors Config.

Sensors diagnostic

Gas Path Check

Memories diagnostic

►Info Service

▼

INFORMATION

Seitron S.p.A.

Tel.+39

0424

567842

Fax.+39

0424

567849

CHEMIST 404S

SN:000001 Ver:1.00

PN:000000 CRC:8BBB

INFO SERVICE

Battery status

Sensors Config.

Sensors diagnostic

Gas Path Check

►Memories diagnostic

▼

INFORMATION

HW Memories ok

Calibration ok

MEMORIES

DIAGNOSTIC

▲

Sensors diagnostic

Gas Path Check

Memories diagnostic

Info Service

►External pobe

INFORMATION

Probe SN --------

EXTERNAL PROBE

Battery status

Sensors Config.

Sensors diagnostic

►Gas Path Check

Memories diagnostic

▼

INFORMATION

Connect to port P-

Apply cap to probe

Press OK to start

GAS PATH CHECK

Connect to port P-

Apply cap to probe

Press OK to start

please wait ...

GAS PATH CHECK

Connect  the  flue  gas  sampling  probe  and  filter  unit  assembly  to  the
instrument;
Fully  insert  the  black  rubber  cap  on  the  gas  probe  tip,  as  shown  in
the following picture:

Black rubber cap

Connect to port P-

Apply cap to probe

Press OK to start

Result: leak

GAS PATH CHECK

Connect to port P-

Apply cap to probe

Press OK to start

Result: tight

GAS PATH CHECK

Connect to port P-

Apply cap to probe

Press OK to start

Result: error

GAS PATH CHECK

Result: error

Check that the probe is connected to
P- input port.

Содержание CHEMIST 400


























































































Результаты поиска

Содержание CHEMIST 400

Отзывы:

Похожие инструкции для CHEMIST 400

Бренды по названию

Популярные бренды

Seitron CHEMIST 400, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание CHEMIST 400

Отзывы:

Похожие инструкции для CHEMIST 400

Бренды по названию

Популярные бренды