Seeley EXQ Скачать руководство пользователя страница 5

Страница: 5 / 20

BREEZAIR EXQ/EZQ/EXS EVAPORATIVE COOLERS INSTALLATION MANUAL

STEP 6

MOUNT COOLER

Mount cooler to the dropper.
Check tank is level.

STEP 16

WATER LEVEL & DRAIN

Set the water level.
Test the drain valve.

STEP 22

CUSTOMER HANDOVER

Show customer how to operate the
cooler. Give them both the MagIQtouch
Controller and cooler owner’s manual.
Explain maintenance requirements.

Page 7

Page 14

Page 16

STEP 4

MOUNT DROPPER

Position, level, secure and flash the

dropper.

STEP 10

REGULATIONS

Read & adhere to the local & national
electrical and plumbing regulations.

STEP 17

REFIT PAD FRAMES

Refit the pad frames before testing the

pump.

STEP 5

CONVEY COOLER

Convey the cooler to the roof.

Note

! Always use 2 people when

handling manually.

STEP 11

INLET SOLENOID

Fit the solenoid.
Connect the cable.
Connect the water supply.
Install the drain pipe.

STEP 18

TEST PUMP

Turn on the cooler and check the water
is evenly distributed to all pads.

STEP 12

DRAIN VALVE

Fit the drain valve.
Connect the discharge system.
Connect the cable to the cooler
electronics.

Page 5

Page 9

Page 14

Page 6

Page 15

Page 11

Page 10

QUICK GUIDE

Содержание EXQ





















Результаты поиска

Содержание EXQ

Отзывы:

Похожие инструкции для EXQ

Бренды по названию

Популярные бренды

Seeley EXQ, Руководство по установке

Результаты поиска

Содержание EXQ

Отзывы:

Похожие инструкции для EXQ

Бренды по названию

Популярные бренды