manualshive.com logo in svg

Security Chimneys International LE LAVAL, Инструкция по установке и эксплуатации, Страница: 26 / 39

Поделиться
Скачать
Security Chimneys International LE LAVAL Скачать руководство пользователя страница 26

 

24 

3.6 

OUTSIDE AIR  

 
It is mandatory

 to install an outside air connection to the LE LAVAL fireplace. The following 

components are required and are included with the fireplace: 

-

 

Outside air kit 

-

 

4" adapter for fireplace connection 

 
The outside air assembly must be installed according to the following requirements : 

 

A)

 

Duct length should be kept to a minimum. The maximum length of a 4" interior diameter 

(100  mm)  insulated  flexible  duct  is  20  ft.  (6.1  m).  The  duct  can  be  extended  to  a 
maximum of 40 ft. (12 m) using a 6" interior diameter (150 mm) insulated flexible duct 
(See note below). 

B)

 

The air intake register must not be installed more than 10 ft. (3050 mm) above the base of 

the fireplace. 

C)

 

The fresh air must come from outside the house.  The air intake must not draw air from 

the attic, basement or garage. 

D)

 

The air intake should be installed where it is not likely to be blocked by snow or exposed 

to extreme wind and away from automobile exhaust fumes, gas meters and other vents. 

E)

 

The duct and register may be installed above or below floor level. 

 
Make  a  4  ¼"  (110  mm)  hole  in  the  outside  wall  of  the  house  at  the  chosen  location.  From 
outside, place the outside air register in the hole (open side down) and fasten the register to the 
wall  with  screws  as  shown  (see  figure  24).    Slip  the  pipe  into  the  insulated  sleeve.    Place  the 
insulated pipe over the register tube and over the fireplace‟s outside air connector (see figure 25). 
At  each  end,  carefully  pull  back  the  insulation  and  plastic  cover  exposing  the  flexible  pipe.  
Using the aluminium tape provided, wrap the tape around the joint between the flexible pipe and 
the  air  inlets.    Carefully  push  the  insulation  and  plastic  cover  back  over  the  pipe.    Using 
aluminium tape, fasten the plastic cover in place. 
 

NOTE

: We recommend not to exceed 20 feet of 4” flexible pipe.  If you require a longer length 

we recommend that you use a 5” diameter flexible pipe for the complete run up to 30 feet and a 
6” diameter pipe for a run of up to 40 feet. 
 

             

 

 

 

 

 

 

Figure 24 

Содержание LE LAVAL








































Отзывы:

Нет отзывов