background image

                                                                500-33530, Rev B 

Output Voltage Ripple and Noise 

< 0.14 Vpp (20 MHz bandwidth  

 limit 

measurement) 

Output Surge Resistance 

2400 Vpk 

Output Over Voltage Protection 

Under any single point  

 

condition, output voltage shall  

 

not exceed 120% of nominal  

 voltage 
Battery Type and Capacity 

Sealed Lead Acid (SLA), 12V,  

 0.8 

Ah 

Battery Standby Time 

20.5 hours dependent on lock  

 

type (FSA or FSE) and usage.   

 

Battery standby time is  

 

designed for EcoFlex lock with  

 

optional H1 controller only (not  

 

for 100 mA load).  H1 controller  

 

draws an average of 5 mA.   

 

The two total current draw is  

 

about 20 mA. 

 

Total Load Current

0.8 Ah Battery Backup Time

20 mA 

20.5 hours 

50 mA 

6.5 hours 

100 mA 

2 hours 

 
 

 

Regulatory Certifications 

 

UL294

, "Access Control System Unit," 6th Edition 

 

UL603

, "Power supply for use with Burglar Alarm System," 5th 

Edition 

 

CAN/ULC-S533

, "Egress Door Securing and Releasing Devices," 

3rd Edition 

 

GreenCircle Certified 

(99% Energy Savings) 

NOTE:

 

50% - battery discharge time from fully charged 
condition. 

Содержание EcoPower EPS-05





















Отзывы: