Seagate STT20000N Скачать руководство пользователя страница 6

Страница: 6 / 70

Table of Contents

Page vi

STT20000A Product Manual

Drive operation and maintenance

Introduction........................................................................................................... 27

Front panel LED operation .................................................................................... 27

Using Travan cartridges ........................................................................................ 28

Loading and unloading tape cartridges............................................................ 28

Setting the write–protect switch ...................................................................... 29

Loading revised firmware from a Seagate firmware cartridge ................................ 29

Drive maintenance ................................................................................................ 30

Caring for tape cartridges ............................................................................... 30

Cleaning the drive read/write head.................................................................. 31

Troubleshooting .................................................................................................... 32

SCSI Interface

Introduction........................................................................................................... 33

SCSI-1 interface ................................................................................................... 33

SCSI-1 status codes....................................................................................... 33

SCSI-1 message codes .................................................................................. 34

SCSI-1 commands ......................................................................................... 35

ANSI X3.131 CONFORMANCE STATEMENT (SCSI-1) ....................................... 36

General features............................................................................................. 36

Commands..................................................................................................... 36

Messages....................................................................................................... 37

Vendor-unique commands .............................................................................. 37

SCSI-2 interface ................................................................................................... 37

SCSI-2 status codes....................................................................................... 37

SCSI-2 message codes .................................................................................. 38

SCSI-2 commands ......................................................................................... 38

ANSI X3.T92 conformance statement (SCSI-2) .................................................... 40

SCSI-2 general features ................................................................................. 40

SCSI-2 commands ......................................................................................... 40

SCSI-2 messages........................................................................................... 41

SCSI-2 vendor-unique commands .................................................................. 41

Command set changes to Incorporate RWW and HDC ......................................... 42

Read-While-Write ........................................................................................... 42

Log Sense Write Error Counts page code (02h)........................................ 42

Hardware data compression ........................................................................... 43

Mode Select / Mode Sense Data Compression page code (0Fh) .............. 43

Parameters that control data compression................................................ 44

Содержание STT20000N







































































Результаты поиска

Содержание STT20000N

Отзывы:

Бренды по названию

Популярные бренды

Seagate STT20000N, Руководство по эксплуатации продукта

Результаты поиска

Содержание STT20000N

Отзывы:

Бренды по названию

Популярные бренды