manualshive.com logo in svg

Seagate STT20000N, Руководство по эксплуатации продукта

Поделиться
Скачать
Seagate STT20000N Скачать руководство пользователя страница 14

Chapter 1

Introduction

Page 6

STT20000A Product Manual

Flash EEPROM

The STT20000 SCSI minicartridge drive incorporates leading-edge technology in the
flash EEPROM, which is useful should the drive's SCSI firmware need to be
upgraded at some point. With the permanently installed electrically up-gradeable
flash EEPROM memory, revised SCSI firmware for the drive can be loaded via any
one of two methods:

• 

Seagate OEM firmware cartridge  (See Chapter 4)

• 

Host SCSI bus

This feature enables qualified OEMs needing to revise the drive firmware to do so
rapidly and at a reduced cost. Flash EEPROM should also prolong the life cycle of a
drive because many new techniques—such as increasing the capacity of the drive
through support for longer tapes—may require only a firmware upgrade.

Software

The STT20000 SCSI minicartridge drive is a cost-effective means of backing up
fixed disks. The software required to perform a disk backup runs under the control of
the host computer's operating system. Compatibility with a wide range of software is
also an important consideration in system integration.

The drive requires any one of the following operating environments: DOS

TM

 version

5.0 or later, Microsoft Windows

TM

 3.1 or later, Microsoft Windows 95, or Windows

NT. The drive operates with many of the popular backup software applications such
as Seagate 's Backup Exec for DOS and Windows, Windows 95, Netware, or
Windows NT.

References

The following standards documents describe some of the technology incorporated in
the drives referenced in this manual.

• 

QIC-121—Implementation of Small Computer System Interface (SCSI-2) for
QIC-Compatible Sequential Storage Devices

• 

QIC-104— Implementation of Small Computer System Interface for QIC-
Compatible Sequential Storage Devices

• 

ANSI X3.127-1987—Unrecorded Magnetic Tape Minicartridge for Information
Exchange:  0.250-inch.

• 

ANSI X3T9.2/86-109—Specifies the Small Computer System Interface-2 (SCSI-2).

• 

QIC-170—Preformatted magnetic minicartridge

• 

QIC-3095-MC—Serial recorded magnetic tape minicartridge

• 

QIC-3220-MC—Serial recorded magnetic tape minicartridge

Содержание STT20000N







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды