Seagate STT20000N Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 70

Seagate STT20000N Скачать руководство пользователя страница 38

Chapter 4

Drive operation and maintenance

Page 30

STT20000A Product Manual

2.

Place the firmware upgrade cartridge record switch to the nonrecord position.
Insert the firmware upgrade cartridge in the drive and observe the amber LED
light on the front of the drive.

3.

Once the upgrade cartridge is inserted, tape motion begins. The drive LED
flashes on and off. Approximately 15 seconds later, tape motion stops, and the
LED continues to flash.

4.

The LED flashes on and off at a steady rate as the firmware upgrade continues.
Approximately 45 seconds later, the drive resets internally, and the tape moves
back and forth, then stops.

5.

The LED light will go off and remain off. Double check that the LED remains off .
Make sure that there is not further tape motion. Remove the upgrade cartridge.

6.

The firmware is now upgraded to the new revision. The drive is operational and
the new firmware is active. Turning power off at this time does not affect the
firmware revision level.

Notes:

Once the firmware upgrade cartridge is inserted in the drive, it is important
that no power interruption occurs while the firmware is loading. DO NOT
POWER OFF THE DRIVE AT THIS TIME. If a power interruption occurs,
the firmware may not be loaded correctly, and the drive may not operate
properly.

If a problem occurs during the firmware loading process, the LED on the front
panel goes out. In that case, the firmware upgrade cartridge may be defective,
or the drive may not be operating correctly.

If after a repeat loading of the firmware cartridge, the same condition is
observed, contact your Seagate sales representative.

Firmware upgrade cartridges are available to qualified Seagate OEM customers.
Contact your Seagate sales representative for information.

Drive maintenance

Minimal maintenance is needed to ensure that your STT20000 SCSI minicartridge
drive operates at peak condition. This section explains how to care for tape
cartridges and how to clean the drive head.

Caring for tape cartridges

Although minicartridge tape cartridges are ruggedly built, they must be handled with
care to preserve the data that they contain. The following points are guidelines for
storing and using minicartridges.

•

Do not open the tape access door of the cartridge or touch the tape itself. One
fingerprint can prevent the drive from reading the tape.

•

Keep the cartridge away from sources of electromagnetic fields, such as
telephones, dictation equipment, mechanical or printing calculators, motors, and

«
...
36
37
38
39
40
...
»

Содержание STT20000N







































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды