manualshive.com logo in svg

Seagate STT20000N, Руководство по эксплуатации продукта

Поделиться
Скачать
Seagate STT20000N Скачать руководство пользователя страница 51

SCSI Interface

Chapter 5

STT20000N Product Manual

Page 43

Hardware data compression

Mode Select / Mode Sense Data Compression page code (0Fh)

Mode Select / Mode Sense Data Compression page code 0Fh has been added to
Seagate tape drives that support hardware data compression. A Seagate tape drive
that supports hardware data compression can be detected by first requesting the
available Mode Sense pages (Mode Sense page code 3Fh). Then if Mode Sense
page 0Fh (Data Compression) is present and the DCC bit is set, the drive supports
hardware data compression. A second method would be to request Mode Sense
page 0Fh (Data Compression). If the drive rejects the request or the DCC bit is not
set, then hardware data compression is not present. The Mode /Select Sense page
code 10 parameter codes for data compression are listed in the following table:

Bit/

Byte

7

6

5

4

3

2

1

0

0

PS

Reserved

Page Code (0Fh)

1

Page Length (0Eh)

2

DCE

DCC

Reserved

3

DDE

RED

Reserved

4

(MSB)

5

Compression Algorithm

6

7

(LSB)

8

(MSB)

9

Decompression Algorithm

10

11

(LSB)

12

Reserved

13

Reserved

14

Reserved

15

Reserved

Содержание STT20000N







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды