manualshive.com logo in svg

Seagate STT20000N, Руководство по эксплуатации продукта

Поделиться
Скачать
Seagate STT20000N Скачать руководство пользователя страница 15

Introduction

Chapter 1

STT20000N Product Manual

Page 7

For more information about a particular QIC standard, contact Quarter-Inch
Cartridge Standards, Inc., c/o Freeman Associates, 311 East Carrillo Street, Santa
Barbara, California 93101.

About this manual

The remaining chapters and the appendices in this manual are briefly described in
the following table. A glossary of terms is also included.

Number

Title

Description

2

Specifications

Contains physical, performance,
environmental, power, and reliability
specifications for the drive and
minicartridges.

3

Installation

Provides cautions, unpacking tips,
inspection information, and
installation/connection steps
including cabling requirements and
connector pinouts.

4

Drive operation

Explains drive operation,
maintenance and troubleshooting

5

SCSI interface

Lists general information about the
SCSI interface. (See Note below.)

6

Tape format

Provides an overview of the QIC-
3220-MC tape format.

7

Theory of operation

Details the functional operation of
various assemblies of the SCSI
drive.

Appendix A

Glossary

Defines key terms.

Appendix B

Acronyms and
Measurements

Lists the acronyms and
measurements used in the manual.

Note:

This manual provides all technical information about the STT20000 SCSI
minicartridge drive for hardware and software development and integration
except complete SCSI information on the SCSI commands themselves.
Refer to the 

SCSI Minicartridge Drive SCSI Manual (P/N 10001652-002)

for detailed information about the SCSI interface, including a complete
command summary.

Содержание STT20000N







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды