Sea Tel DAC-2202, Инструкция по установке и эксплуатации

Страница: 12 / 115

Antenna Menu Satellite Menu Ship Menu
Status
Menu
Power-Up Menu
The possible values are:
70/140 MHz
SCPC VER 4.XX
DVB/SCPC V3 SCPC VER 5.XX
DVB VER 4.XX NBIF VER 4.XX
DVB VER 5.XX No RCVR Found
This is the model configuration
and software version of the PCU.
OR
Bring up the cursor. Then press the UP arrow key, or the TRACK key, to
toggle the Tracking ON/OFF. Press the DOWN arrow key to toggle
through the list of possible BAND selections (the selections displayed
are dependent on the parameter value entered for TRACK DISP).
To
Execute
To
EXIT
CONTROL
TRACKING OFF KuLo
In DVB Mode “FREQ 1100 AGC 1234” will be displayed. In SCPC Mode
“MHz 1111 AGC 1234” will be displayed. See FEC setting below.
If SCPC is selected, the receiver will be in SCPC Mode. All other FEC rate
settings are DVB Mode. The mode selected effects the displays above.
OR
Use the LEFT or RIGHT arrow keys to move the antenna Left/Down/
CCW or Right/Up/CW in Azimuth.
Use the UP or DOWN arrow keys to move the antenna Up or Down
in Elevation.
Distributed By: _________________________________________________
Authorized Sea Tel Dealer
Phone: ______________________________
OR
Use the UP arrow key to turn the search pattern ON. Use the DOWN
arrow key to turn search OFF.
To
Execute
To
EXIT
CONTROL
SEARCH 2 OFF
OR
LLLL - Comms Error Count - display (only).
RRRR - Error Code - indicates the SUM of the discrete error(s) that
have occurred. Pressing LEFT then press UP arrow key clears error
count, status code and extinguishes the Error LED.
To
Execute
To
EXIT
STATUS
ERROR LLLL RRRR
OR
Remote Auxiliary read diagnostic display. Typically used to display
temperature of EIRP readings.
To
Execute
To
EXIT
STATUS
REMOTE AUX 1234
OR
The Latitude of the ship should be updated by the GPS antenna on the
antenna pedestal. If the Latitude is not being automatically updated,
manually set the correct position value and Hemisphere.
To
Execute
To
EXIT
LAT 38.0 N
OR
The Longitude of the ship should be updated by the GPS antenna on
the antenna pedestal. If the Longitude is not being automatically
updated, manually set the correct position value and Hemisphere.
To
Execute
To
EXIT
LON 122.0 W
OR
Set to the Heading value of the Gyro Compass (NMEA 0183, SBS or
Synchro).
To
Execute
To
EXIT
HDG 000.0 000.0
OR
Set to the desired Azimuth value that you want to target the antenna
to.
To
Execute
To
EXIT
AZ 123.4
# AGC 1234
OR
Set to the desired Elevation value that you want to target the antenna
to.
To
Execute
To
EXIT
EL 056.7
# AGC 1234
OR
Set to the desired Relative position that you want to target the antenna
to.
To
Execute
To
EXIT
REL 000.0 AGC 1234
OR
AutoPol mode will automatically keep the polarization of the feed
optimized. Refer to the Optimizing Polarization information in the
Antenna manual.
To
Execute
To
EXIT
POL 0000 AGC 1234
OR
SEA TEL INC – MASTER
DAC-2202 VER 6.07
SEA TEL INC – RCVR
DVB VER 5.04
SEA TEL INC – IO MOD
COMMIF VER 1.12
SEA TEL INC – REMOTE
4009 VER 2.00
OR
OR
LAT 38 N LON 122 W
HDG 000.0 000.0 SAT 101 W THRS 1234
FREQ 1100 NID 1234 AZ 123.4 EL 056.7
REL 234.5 AGC 1234
Set to the desired Satellite Longitude value and Hemisphere.
To
Execute
To
EXIT
SAT 101.0 W
OR
Auto Threshold will automatically set this value. If you turn Auto
Threshold OFF, refer to the ACU manual Tracking and Searching
information for manually setting the Threshold value.
To
Execute
To
EXIT
THRS 1234
OR
Set to the desired MHz frequency that you want to use for
Tracking.
To
Execute
To
EXIT
FREQ 1100 AGC 1234
OR
Set to the desired Baud Rate (symbol rate), OR the KHz frequency,
that you want to use for Tracking.
To
Execute
To
EXIT
Baud 20000 AGC 1234
OR
Set to the desired Tone ON/OFF state.
To
Execute
To
EXIT
Tone OFF AGC 1234
OR
Set to the desired Volt selection. Available selections are; HORZ
(18VDC), LHCP (18VDC), VERT (13VDC) or RHCP (13VDC).
To
Execute
To
EXIT
Volt HORZ AGC 1234
OR
Set to the desired desired FEC selection. Refer to the ACU manual for a
list of current selections.
To
Execute
To
EXIT
FEC AUTO AGC 1234
OR
Set to the known Polarization skew (in whole degrees) for the satellite
currently being, or intended to be, tracked. Values less than 0000 will
be displayed as a negative value.
To
Execute
To
EXIT
Skew 0000 AGC 1234
OR
Set to the desired NID value (refer to the ACU manual).
To
Execute
To
EXIT
NID 0000 AGC 1234
OR