Sea-doo 2003 LRV DI Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 88

Sea-doo 2003 LRV DI Скачать руководство пользователя страница 47

45

TYPICAL

1. Shift lever in neutral position

TYPICAL

1. Reverse gate in middle neutral position

To obtain reverse, pull shift lever com-
pletely. The reverse gate will be in down-
ward position, directing all the thrust to-
ward the front of the watercraft.

TYPICAL

1. Shift lever in reverse position

TYPICAL

1. Reverse gate in downward reverse position

NOTE:

To obtain maximum efficiency

and control from the reverse, increase
engine speed to slightly above idle.
Too much RPM will create water tur-
bulence and reduce reverse efficiency.

In reverse position, turn the handlebar
in the opposite direction that you want
to move the rear of the watercraft.

For example, to steer the rear of the
watercraft to the left side, turn the han-
dlebar to the right side.

TYPICAL

1. Handlebar turned to the right side
2. Rear of

watercraft

moving to the left side

F07L0RY

1

F07J0NY

1

F07L0SY

1

WARNING

Shift lever should only be used when
the engine is idling and watercraft is
completely stopped. Do not use re-
verse to stop the watercraft.

F07J0OY

1

F07A0CY

1

2

smo2003-005a.book Page 45 Friday, November 1, 2002 8:25 AM

«
...
45
46
47
48
49
...
»

Содержание 2003 LRV DI

























































































Отзывы:

Нет отзывов