Sea-doo 2003 LRV DI Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 88

Sea-doo 2003 LRV DI Скачать руководство пользователя страница 46

44

OPERATING INSTRUCTIONS

Principle of Operation

Propulsion

The engine is directly coupled to a drive
shaft which, in turn, rotates an impel-
ler. This impeller is accurately adjusted
in a housing where the water is drawn
up from underneath the watercraft.
Then the water flows through the im-
peller to a venturi. The venturi acceler-
ates the water and produces thrust to
move the watercraft. Depressing the
throttle lever increases engine speed
and therefore watercraft speed.

TYPICAL

The shift lever should be in the forward
position in order for the watercraft to ad-
vance.

Neutral and Reverse

To find the neutral, set in reverse then
push back until the watercraft stops
moving backwards.

The reverse gate will be in the middle
position, directing half of the thrust to-
ward the front of the

watercraft

to min-

imize watercraft movement.

WARNING

Always perform the PRE-OPERATION
CHECKS before operating the wa-
tercraft. Become thoroughly famil-
iar with all controls and the function
of each. Should any control or in-
struction not be fully understood,
refer to an authorized SEA-DOO
dealer.

WARNING

Whenever the engine is to be start-
ed, the operator and passenger(s)
should always be properly sitting
on the watercraft and be wearing
protective clothing including a
Coast Guard approved PFD and a
wet suit bottom.

F01J3YY

WARNING

Keep away from intake grate while
engine is on. Items such as long
hair, loose clothing or personal flo-
tation device straps can become
entangled in moving parts result-
ing in severe injury or drowning.

WARNING

Never use jet pump components as
a supporting point to board the wa-
tercraft. Shift lever should only be
used when the engine is idling and
watercraft is completely stopped.
Never rev the engine at high RPM
in reverse. Do not use reverse to
stop the watercraft. Only use re-
verse at slow speed and for the
shortest time possible. Always en-
sure the path behind is clear of ob-
jects and persons including chil-
dren playing in shallow water.

WARNING

When the

watercraft

is in neutral

position, the drive shaft and impel-
ler are still turning.

smo2003-005a.book Page 44 Friday, November 1, 2002 8:25 AM

«
...
44
45
46
47
48
...
»

Содержание 2003 LRV DI

























































































Отзывы:

Нет отзывов