Sea-doo 2003 LRV DI Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 88

Sea-doo 2003 LRV DI Скачать руководство пользователя страница 42

40

BREAK-IN PERIOD

CAUTION:

Scrupulously follow the

instructions of this section. Failure
to do so may reduce the engine’s life
and/or performance.

With SEA-DOO watercraft powered by
Rotax

®

engines, a break-in period of 10

hours is required before continuous
operation at full throttle.

With the DI engine, in order to achieve
a good break-in, vary the engine speed
every few minutes with brief wide
open throttle accelerations of up to 15
seconds.

CAUTION:

Continued wide open

throttle runs and prolonged cruising
without speed variations should be
avoided, this can cause engine dam-
age during the break-in period.

CAUTION:

Remove and clean spark

plugs after engine break-in.

NOTE:

Adding injection oil in the fuel

tank for the break-in has no noticeable
effects on a DI engine.

10-Hour Inspection

It is highly recommended that after the
first 10 hours of operation, the water-
craft be checked by an authorized
SEA-DOO dealer. This inspection will
also provide the opportunity to discuss
the unanswered questions you may
have encountered during the first hours
of operation.

The 10-hour inspection is at the ex-
pense of the watercraft owner.

smo2003-005a.book Page 40 Friday, November 1, 2002 8:25 AM

«
...
40
41
42
43
44
...
»

Содержание 2003 LRV DI

























































































Отзывы:

Нет отзывов