Sea-doo 2003 LRV DI Скачать руководство пользователя страница 37

Страница: 37 / 88

22) Bow and Stern Eyelets

Bow Eyelet

Eyelets can be used for mooring, tow-
ing and as a tie-down point during traile-
ring.

1. Bow eyelet

Stern Eyelet

This eyelet allows a rope with a hook,
a closed end or an open end to be at-
tached.

TYPICAL

1. Stern eyelet

23) Fender Cleats

These cleats can be temporarily used for
docking, while refueling for fender instal-
lation.

CAUTION:

Do not use the cleats for

securing baggage or as a tie-down
point for trailering or mooring. Never
use mooring cleats to pull or lift the
watercraft.

TYPICAL

1. Fender cleats (each side)

24) Footboard

User’s feet should rest on the footboard
when riding.

25) Boarding Platform

Provides a large surface for easier board-
ing from rear of watercraft.

26) Boarding Step

A convenient step to help reboarding
the watercraft.

TYPICAL

1. Boarding step

F00L0EY

F07L0YY

F07L0XY

F07L1HY

smo2003-005a.book Page 35 Friday, November 1, 2002 8:25 AM

Содержание 2003 LRV DI

























































































Результаты поиска

Содержание 2003 LRV DI

Отзывы:

Sea-doo 2003 LRV DI, Руководство оператора, Страница: 37 / 88

Результаты поиска

Содержание 2003 LRV DI

Отзывы: