Sea-Bird Scientific SBE 37-SM Скачать руководство пользователя | Manualshive

Страница: 79 / 87

background image

Manual revision 041

Appendix IV: AF24173 Anti-Foulant Device

SBE 37-SM RS-232

79

PRECAUTIONARY STATEMENTS

HAZARD TO HUMANS AND DOMESTIC ANIMALS

DANGER

Corrosive

- Causes irreversible eye damage and skin burns. Harmful if swallowed. Harmful if

absorbed through the skin or inhaled. Prolonged or frequently repeated contact may cause allergic
reactions in some individuals. Wash thoroughly with soap and water after handling.

PERSONAL PROTECTIVE EQUIPMENT

USER SAFETY RECOMMENDATIONS

Users should:



Remove clothing immediately if pesticide gets inside. Then wash thoroughly and put on
clean clothing.



Wear protective gloves (rubber or latex), goggles or other eye protection, and clothing to
minimize contact.



Follow manufacturer’s instructions for cleaning and maintaining PPE. If no such instructions
for washables, use detergent and hot water. Keep and wash PPE separately from other
laundry.



Wash hands with soap and water before eating, drinking, chewing gum, using tobacco or
using the toilet.

ENVIRONMENTAL HAZARDS

Do not discharge effluent containing this product into lakes, streams, ponds, estuaries, oceans, or other
waters unless in accordance with the requirements of a National Pollutant Discharge Elimination
System (NPDES) permit and the permitting authority has been notified in writing prior to discharge.
Do not discharge effluent containing this product to sewer systems without previously notifying the
local sewage treatment plant authority. For guidance contact your State Water Board or Regional
Office of EPA. This material is toxic to fish. Do not contaminate water when cleaning equipment or
disposing of equipment washwaters.

PHYSICAL OR CHEMICAL HAZARDS
Do not use or store near heat or open flame. Avoid contact with acids and oxidizers.

DIRECTIONS FOR USE
It is a violation of Federal Law to use this product in a manner inconsistent with its labeling. For use
only in Sea-Bird Electronics’ conductivity sensors. Read installation instructions in the applicable
Conductivity Instrument Manual.

«
...
77
78
79
80
81
...
»

Содержание SBE 37-SM
























































































Отзывы:

Нет отзывов

Похожие инструкции для SBE 37-SM

Бренд: Magna Страницы: 82

PortaSens II C16

Бренд: Ozone Solutions Страницы: 10

EasyLog EL-USB Series

Бренд: Lascar Electronics Страницы: 2

XORAYA ML-N4000

Бренд: X2E Страницы: 190

Data Station Plus

Бренд: red lion Страницы: 8

MODAT-550A Series

Бренд: IEI Technology Страницы: 79

Бренд: Ebro Страницы: 36

Бренд: Xylem Страницы: 8

Бренд: MadgeTech Страницы: 16

Бренд: iDuino Страницы: 4

Бренд: berlinger Страницы: 2

Бренд: Fluke Страницы: 254

Бренд: Sensitech Страницы: 2

Бренд: Alpha Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды