Section 3: Setting Up System
SBE 45 Interface Box
13
5.
If the SBE 45 was set to
AutoRun=Y
and its J1 jumper was set to pins 1
and 2 (begin sampling automatically on power up), data from the Interface
Box begins scrolling on the screen. Each time data is received from an
instrument (SBE 45, SBE 38, and NMEA navigation device), the
corresponding LED on the Interface Box flashes. If data is
not received, is incorrect, or is not updating properly for some or
all instruments:
•
Verify that the instrument is connected to the Interface Box and that
the proper cable is used.
•
Check the baud rate of each instrument (SBE 45, SBE 38, and NMEA
navigation device). These baud rates must be less than the baud rate
for communication between the Interface Box and the computer. If
necessary, connect each instrument directly to the computer and use
SEATERM to reset its baud rate. See the appropriate instrument
manual for details.
•
Check that the setup of each instrument is compatible with operation
with the Interface Box. See
Setting Up Instruments
.
•
If data is not received from a NMEA navigation device, see
Appendix I: NMEA Data
for troubleshooting information.
6.
If desired, type
Stop
and press the Enter key to stop the scrolling data.
Note that you can send commands to the Interface Box and/or attached
instruments while it is transmitting data, but it easier to see what the
commands and responses are without the scrolling data.
7.
Display Interface Box status information by clicking Status on the
Toolbar. The display looks like this:
SBE45 Junction Box V 1.4
SBE 45 baud rate = 4800
SBE 38 baud rate = 4800
NMEA baud rate = 4800
standard output format
Note that the baud rates shown must be less than the baud rate for
communication between the Interface Box and the computer.
8.
Verify SBE 45 setup by putting the Interface Box in SBE 45 mode:
A.
Type
Connect45
and press the Enter key. If the SBE 45 is set for
AutoPower=Y
and
SingleSample=N
, SBE 45 data will scroll across
the screen. Type
Stop
and press the Enter key to stop the scrolling
data.
B.
Send desired setup commands to the SBE 45 (see
Setting Up
Instruments
for required setup parameters).
C.
Type
GO
and press the Enter key to restart SBE 45 sampling. SBE 45
data should begin scrolling on the screen.
D.
Type @ to return to Normal mode for communication with the
Interface Box.
9.
Verify SBE 38 setup by putting the Interface Box in SBE 38 mode:
A.
Type
Connect38
and press the Enter key. If the SBE 38 is set for
AutoPower=Y
, SBE 38 data will scroll across the screen. Type
Stop
and press the Enter key to stop the scrolling data.
B.
Send desired setup commands to the SBE 38 (see
Setting Up
Instruments
for required setup parameters).
C.
Type
Go
and press the Enter key to restart SBE 38 sampling. SBE 38
data should begin scrolling on the screen.
D.
Type @ to return to Normal mode for communication with the
Interface Box.
10.
Type
Start
and press the Enter key to restart data transmission through
the Interface Box.
The system is ready for deployment.
Note:
You must restart SBE 45 and SBE 38
sampling using
Go
before returning to
Normal mode, or these instruments
will not transmit their data to the
Interface Box.
Note:
The Interface Box outputs data at the
SBE 45’s data output rate. If the
SBE 45 is not outputting any data,
data from the SBE 38 and/or NMEA
navigation device will not appear at all.
75
Содержание SBE 45 MicroTSG
