SCIFIT ISO7000R Скачать руководство пользователя страница 55

Страница: 55 / 82

Installation of Left Pedal

1. While looking at the left pedal from the left side view (shown above), start

the pedal bolt threads by rotating the pedal bolt counterclockwise, by
hand, until you can’t tighten any further.

2. Place either a 15mm or 5/8” open end wrench on the wrench flats on the

pedal bolt and tighten.

Installation of Right Pedal

1. While looking at the right pedal from the right side view (shown above),

start the pedal bolt threads by rotating the pedal bolt clockwise, by hand,
until you can’t tighten any further.

2. Place either a 15mm or 5/8” open end wrench on the wrench flats on the

pedal bolt and tighten.

Chain Removal / Replacement

Removal

1. Locate the master link (P2234) in the chain.
2. Place the head of a flat-head screwdriver in the middle of the retaining clip

prongs.

3. Twist screwdriver to separate prongs and remove the retaining clip from

the master link.

4. Remove the flat master link plate.
5. Pull the master link out of the chain from the opposite side of the retaining

clip.

6. Remove chain from the unit.

Содержание ISO7000R



















































































Результаты поиска

Содержание ISO7000R

Отзывы:

Бренды по названию

Популярные бренды

SCIFIT ISO7000R, Руководство по обслуживанию

Результаты поиска

Содержание ISO7000R

Отзывы:

Бренды по названию

Популярные бренды