manualshive.com logo in svg

SCHUNK 1487754, Сборка и руководство по эксплуатации

Поделиться
Скачать
SCHUNK 1487754 Скачать руководство пользователя страница 33

Maintenance

10 Maintenance

10.1 Safety

Maintenance work may only be carried out by qualified personnel.

 WARNING

Risk of injury due to incorrect maintenance or troubleshooting

•

Check the proper functioning of the product, especially the
safety features, after every maintenance or troubleshooting
operation.

 CAUTION

Improper installation or maintenance

Personal injury or damage to property

•

Prior to installation and before maintenance work, the
product must be disconnected from the power supply,
depressurized (vented to the atmosphere) and secured
against unauthorized restart.

10.2 Cleaning

The Matrix-Plate must be cleaned before each machining process.
Visible contamination must be suctioned or blown off, and then
the Matrix-Plate wiped down with a slightly damp cloth.

10.3 Wear of the Sealing Gasket

If the sealing gasket has any cracks or any other damage, it must
be replaced or the damaged part replaced.

10.4 Milling the Matrix-Plate

To ensure maximum precision during subsequent processing, the
Matrix-Plate can be milled (even several times) when it is clamped
on the machine table. This can also be useful to obtain a new flat
surface if the surface of the Matrix-Plate becomes damaged.
Note the following:
• The zero point of the system changes.
• The groove depth of the grid is reduced.
• If more than 0.5 mm of material is removed, a sealing gasket

with ø = 3 mm must be used.
This prevents the sealing gasket from being compressed
between the Matrix-Plate and the workpiece, resulting in
inaccuracies.

33

01 | Matrix-Plate SMPL | Assembly- and Operating Manual | en-US | 0489081

Содержание 1487754









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды