manualshive.com logo in svg

SCHUNK 1487754, Сборка и руководство по эксплуатации

Поделиться
Скачать
SCHUNK 1487754 Скачать руководство пользователя страница 17

Installation

3. Keep hose lines free of bends and crimps.
4. Lay hose lines in such a way that they do not rub.

 CAUTION

Vacuum close to the eye

Severe eye injury!

•

Wear eye protection.

•

Do not look into vacuum openings such as suction lines and
hoses.

NOTE

If a large suction volume is required (e.g. in the case of leakage or
porous workpieces), it can make sense to use an additional
vacuum connection particularly for larger Matrix-Plate variants.
A larger or an additional vacuum generator may also be used if
necessary.

Note:

If the Matrix-Plate is used in wet areas, we strongly recommend
connecting a water separator upstream of the vacuum generator
to prevent damage to the vacuum generator. This function is
already integrated into the vacuum units from SCHUNK.

6.4 Connecting Several Matrix-Plates

The required clamping area can be increased as required by
combining several Matrix-Plates with each other. All plates with
the same slot size can be added to each other on all four sides,
enabling larger workpieces to be clamped without any problems.
The outer dimensions of the Matrix-Plates are irrelevant here.
The following steps describe the process for connecting several
Matrix-Plates (1):
1. On the side at which another Matrix-Plate is to be connected,

remove the side stops including the knurled nuts and the set
screws.

2. Remove at least one of the front-side sealing screws with collar

(2) from the vacuum ducts and screw in the hollow bolt (4),
which is available as an accessory, with the sealing ring (3). The
sealing screws on the second Matrix-Plate must also be
removed. These bores remain open, however, and are closed
later with the hollow bolt when connecting the Matrix-Plates
together.

17

01 | Matrix-Plate SMPL | Assembly- and Operating Manual | en-US | 0489081

Содержание 1487754









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды