manualshive.com logo in svg

SCHUNK 1487754, Сборка и руководство по эксплуатации

Поделиться
Скачать
SCHUNK 1487754 Скачать руководство пользователя страница 19

Start of Operations

7 Start of Operations

7.1 Personnel Qualification

Unqualified personnel cannot recognize dangers and are therefore
exposed to higher risks!
1. Only instruct qualified personnel to perform the tasks

described in these operating instructions.

2. The product may only be operated by persons who have

undergone appropriate training.

3. Electrical work and installations may only be carried out by

qualified electrical specialists.

4. Assembly and maintenance work must only be carried out by

qualified personnel.

7.2 Before Initial Start of Operations

Before the initial start of operations following installation, repair,
servicing or maintenance work, you must check the following:
• All mechanical connectors are properly attached and secured.
• All screws and nuts are tightened to specified torques.
• All components are installed.
• The safety distances have been maintained.
• The electrical cable and supply hoses are properly routed.
• The EMERGENCY STOP switch for the overall system is working.

 CAUTION

Noise pollution due to incorrect installation of the pressure and
vacuum connections

Hearing damage

•

Correct installation.

•

Wear ear protectors.

 CAUTION

Vacuum close to the eye

Severe eye injury!

•

Wear eye protection.

•

Do not look into vacuum openings, e.g. suction cups.

19

01 | Matrix-Plate SMPL | Assembly- and Operating Manual | en-US | 0489081

Содержание 1487754









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды