Schmalz FMHD Series Скачать руководство пользователя страница 5

Страница: 5 / 52

30.30.01.01648/03

www.schmalz.com

EN | 5

Safety Instructions

Classification of Safety Instructions

1.1

Danger

This warning informs the user of a risk that will result in death or serious injury if it is not avoided.

DANGER

Type and source of danger

Consequence

► Remedial action

Warning

This warning informs the user of a risk that could result in death or serious injury if it is not avoided.

WARNING

Type and source of danger

Consequence

► Remedial action

Caution

This warning informs the user of a risk that could result in injury if it is not avoided.

CAUTION

Type and source of danger

Consequence

► Remedial action

Attention

This warning informs the user of a risk that could result in damage to property if it is not avoided.

ATTENTION

Type and source of danger

Consequence

► Remedial action

General Notes

This symbol is used when important notes and information regarding the use of the machine/the sys-
tem/the device are provided.

Note/information

Содержание FMHD Series





















































Результаты поиска

Содержание FMHD Series

Отзывы:

Бренды по названию

Популярные бренды

Schmalz FMHD Series, Руководство по эксплуатации

Результаты поиска

Содержание FMHD Series

Отзывы:

Бренды по названию

Популярные бренды