manualshive.com logo in svg

Schmalz FMHD Series, Руководство по эксплуатации

Поделиться
Скачать
Schmalz FMHD Series Скачать руководство пользователя страница 40

 

40 |   EN 

www.schmalz.com 

30.30.01.01648/03 

  Valve Plate 

8.7

For enhanced maintenance, the valve plate can be unscrewed and removed. This is where the  valves 
are  located.  For  cleaning  purposes,  the  attached  masking  films  can  be  removed  so  that  the  spherical 
bearings  can  be  removed.  In  order  to  ensure  that  the  area  gripper  continues  to  work  optimally,  the 
valves must be cleaned regularly, especially when exposed to resins. We recommend replacing the old 
masking film with a new masking film during cleaning. If necessary, heavily contaminated bearings can 
also be replaced. See chapter 9.9  
Here the operator also has the  option to make a second, identical  plate available for exchange during 
maintenance. 

 

  Sealing Plate 

8.8

Check the sealing plates for wear, tears and leakage on a regular basis and replace them as necessary. 
The sealing plates must also be replaced if you notice that the vacuum achieved is constantly declining 
when handling the same parts.  
Minimum recommended vacuum: 250 mbar when a workpiece is picked up.  
For  systems  that  are  designed  to  require  higher  vacuum,  the  minimum  vacuum  must  be  adjusted  ac-
cordingly when the sealing plates are replaced.  
 

 

The  foam  may  not  be  cleaned  with  a  compressed-air  gun.  This  would  make  the 
foam permeable to air in the places where compressed air was applied. 

 

If  the  sealing  plate  shows  mechanical  damage,  it  can  be  repaired  up  to  a  certain 
point  using  standard  vulcanizing  adhesive  (e.g.  adhesive  for  repairing  the  inner 
tubes of bicycles). 

 

Replacing the sealing plates 

 

In order  to  easily  replace  the  sealing  plates,  the  quick-change  plate 
can  be  removed  in  accordance  with  the  operating  instructions.  This 
means that it is not necessary to replace the sealing plate overhead. 

 

Remove the sealing plate from the quick-change system. 

 

Clean the surfaces. In order to maintain optimal hold of the new seal-
ing  plate, the surface must be free of dust, oil, oxides and adhesive 
residues. 

 

Remove the protective film from the adhesive strip of the new sealing 
plate. 

 

Press  the  sealing  plate  firmly  onto  the  entire  surface  without  any 
wrinkles (e.g. with a roller). 

 

The openings of the sealing plate and valves must be aligned. 

 

Processing temperature: a range of +10° C to +40° C is recommended for the object tempera-
ture and the ambient temperature. 
 

 

The sealing mat is asymmetrical. Observe the alignment. 

Video 

www.schmalz.com/

replacing-sealing-

foam

 

Содержание FMHD Series





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды