www.scheppach.com /
+(49)-08223-4002-99 /
+(49)-08223-4002-58
24 | GB
• Insert bolts (not included) and tighten securely with
lock washers and hex nuts (not included). Note: All
bolts should be inserted from the top. Install the
lock washers and hex nuts from the underside of
the workbench.
Clamping belt/disc sander to work bench
If your belt/disc sander is to be used as a portable
tool, it is recommended you fasten it permanently to
a mounting board that can easily be clamped to a
workbench or other stable surface.
The mounting board should be of sufficient size to
avoid tipping while belt/disc sander is in use. Any
good grade plywood or chipboard with a 3/4 in. (19
mm) thickness is recommended.
• Mark holes on board where belt/disc sander is to
be mounted using holes in the base as a template
for hole pattern.
• Follow last three steps in section Mounting Belt/
Disc Sander to Workbench.
If lag bolts are used, make sure they are long enough
to go through holes in belt/disc sander base and
material the belt/ disc sander is being mounted to.
If machine bolts are used, make sure bolts are long
enough to go through holes in belt/disc sander, the
material being mounted to, and the lock washers and
hex nuts.
8.6 On/Off switch (12)
• The grinder/sander can be switched on by press-
ing the green button „1“.
•
To switch off the grinder/sander you must press
the red button „0“.
Warning: Do not reach across the sanding disc to
turn the belt/disc sander ON or OFF. Contact with the
sanding disc can result in serious personal injury.
8.7 Grinding/sanding
•
Always hold the workpiece firmly during grinding/
sanding.
• Do not exert excessive pressure.
• To prevent the abrasive paper from becoming worn
on one side, the workpiece should be moved to
and from on the grinding/sanding belt or grinding/
sanding plate as you grind/sand.
• Important! Pieces of wood should always be sand-
ed with the grain to prevent them splitting. Impor-
tant. If the grinding wheel or the grinding/sanding
belt becomes jammed during operation, please re-
move the workpiece until the tool reaches its top
speed again.
8.2. Changing the grinding/sanding belt (6)
(fig. 6 - 9)
• Pull out the power plug
• Remove the screws (18).
• Remove the grinding/sanding belt guard (19).
• Turn the grinding/sanding tensioner (10) to the
right in order to reduce the tension on the grind-
ing/sanding belt (6).
• Remove the grinding/sanding belt (6) to the rear.
• Mount and the new grinding/sanding belt in re-
verse order. Important. Note the running direction:
On the housing and on the inside of the grinding/
sanding belt!
8.3. Adjusting the grinding/sanding belt (6)
• Pull out the power plug
• Push the grinding/sanding belt (6) by hand slowly
in the running direction.
• The grinding/sanding belt (6) must run centrally on
the grinding/sanding surface. If not, you can use
the knurled screw (8) to make adjustments.
8.4. Moving the grinding/sanding position of the
grinding/sanding belt (6)(Fig. 10-12)
• Loosen the Allen screw (5)
• Move the grinding/sanding belt (6) upwards into
the desired position.
•
Tighten the Allen screw (5) again to fix this posi
-
tion.
• In this position you can use the grinding/ sanding
table to support the workpiece. To do this, first
loosen the two Allen screws (17) and then remove
the stop rail (7). The grinding table can now be
pushed into the hole in the holder tube (20) and
fixed with the screw (1)
8.5. Replacing the abrasive paper on the grind-
ing/sanding disk (11)
Dismantle the bottom wheel guard (15) by removing
the 2 screws (16). Pull the sanding/ grinding paper
off the sanding/grinding disk (11) and attach the new
sanding/grinding paper (quick-fit fastening system).
Mounting belt/disc sander to work bench
If your belt/disc sander is to be used in a permanent
location, it is recommended you secure it to a work-
bench or other stable surface.
• Mark holes on workbench where belt/disc sander
is to be mounted using holes in the base as a tem-
plate for hole pattern.
• Drill holes through workbench.
• Place belt/disc sander on workbench aligning
holes in the base with holes drilled in the work-
bench.
