Scheppach 5910121917, Перевод оригинального руководства пользователя

Страница: 35 / 64


www.scheppach.com
GB | 35
9. Commissioning
m
CAUTION
Please observe the legal provisions from the noise
protection ordinance.
Before each start-up, check the device for the follow-
ing:
• Check the fuel system for leakage
• Faultless condition and completeness of the guards
and the cutting device
• Tight fit of all screw connections
• Smooth running of all moving parts
Working instructions
Familiarise yourself with handling the chainsaw be-
fore use.
9.1 Starting the engine
m
ATTENTION
Always pull the start pull cord (4) out straight. Hold the
handle of the start pull cord (4) firmly when the pull
cord (4) winds back in. Never let the start pull cord (4)
whip back in.
9.1.1 Starting the engine when cold
m
WARNING
Engage the chain brake before every start-up (push
the hand guard (1) forward).
m
ATTENTION
Never allow the start pull cord (4) to spin back. This
can result in damage.
• Remove the cover (27) from the guide bar (16).
• Set the chainsaw down on a firm and level surface.
The saw chain (17) must not come into contact with
the ground.
• Push the front hand guard (1) forwards until it latch-
es into place. The saw chain (17) is clamped by the
chain brake.
• Press the fuel pump primer (7) 6x.
• Switch the ON/OFF switch (6) to “ON”.
• Pull out the cold start (choke) lever (8) ( ).
• Place the tip of your shoe in the rear hand guard
(12) (see fig. C).
• Hold the chainsaw firmly by the front handle (2) and
pull the start pull cord (4) out slowly until you feel the
first resistance.
• Now pull the start pull cord (4) and the engine should
start. If the engine does not start, repeat the process.
So long as the cold start (choke) (8) lever is pulled
out ( ) the engine will run for only a short time and
then stop.
8.4 Filling with chain oil
m
WARNING
Only fill the saw chain oil when the engine is switched
off and has cooled down. There is a risk of fire!
Never work without chain lubrication! If the saw chain
runs dry, the cutting gear will be irreparably destroyed
in a short time.
Always check chain lubrication before working.
NOTE
Use only saw chain oil. Preferably biodegradable. Do
not use waste oil, engine oil, etc.
Check during work that the chain lubrication is work-
ing.
• Always clean the area around the chain oil tank cap
(14) before filling so that no dirt falls into the chain
oil tank. Use a dry, lint-free cloth for this purpose.
• Lay the device on its side with the chain oil tank cap
(14) is facing upwards.
• Turn the chain oil tank cap (14) anti-clockwise and
open it. The chain oil tank cap (14) is connected to
an anti-loss device in the chain oil tank and thus
cannot fall off.
• Pour the chain oil into the chain oil tank. Do not spill
chain oil when refuelling and do not fill the chain oil
tank to the brim.
• Wipe up spilled chain oil immediately.
• Turn the chain oil tank cap (14) clockwise to close it.
8.5 Tensioning and checking the saw chain
m
WARNING
Put on protective gloves! Danger of injury due to the
sharp cutting teeth!
Check the chain tension regularly before each start-
up.
• Before tensioning, loosen the two fixing nuts (20) a
little with the spark plug wrench / slotted screwdriver
(28).
• Turn the chain tensioning screw (21) clockwise with
the spark plug wrench / slotted screwdriver (28) to
increase the tension.
• Tighten the two fixing nuts (20) with the spark plug
wrench / slotted screwdriver (28).
• The saw chain (17) must be in contact with the un-
derside of the guide bar. Check whether the saw
chain (17) can be pulled over the guide bar (16) by
hand (with the chain brake released, pull the front
hand guard (1) back).
NOTE
A new saw chain (17) stretches and needs to be re-
tensioned more often.