Scheppach 5901309903, Перевод оригинального руководства по эксплуатации

Страница: 23 / 36


www.scheppach.com

service@scheppach.com

+(49)-08223-4002-99

+(49)-08223-4002-58
7
Use the correct electric tool
– Do not use low-output electric tools for heavy work.
– Do not use the electric tool for purposes for which
it is not intended. For example, do not use hand-
held circular saws for the cutting of branches or
logs.
–
Do not use the electric tool to cut firewood.
8
Wear suitable clothing
– Do not wear wide clothing or jewellery, which can
become entangled in moving parts.
–
When working outdoors, anti-slip footwear is
recommended.
– Tie long hair back in a hair net.
9
Use protective equipment
–
Wear protective goggles.
– Wear a mask when carrying out dust-creating
work.
10
Connect the dust extraction device if you will
be processing wood, materials similar to wood,
or plastics.
–
If connections for dust extraction and a collect-
ing device are present, make sure that they are
connected and used properly.
–
When processing wood, materials similar to
wood, and plastics. operation in enclosed
spaces is only permitted with the use of a suit-
able extraction system.
11
Secure the workpiece
– Use the clamping devices or a vice to hold the
workpiece in place. In this manner, it is held
more securely than with your hand.
– An additional support is necessary for long work-
pieces (table, trestle, etc.) in order to prevent the
machine from tipping over.
–
Always press the workpiece firmly against
the working plate and stop in order to prevent
bouncing and twisting of the workpiece.
12
Avoid abnormal posture
– Make sure that you have secure footing and
always maintain your balance.
–
Avoid awkward hand positions in which a sudden
slip could cause one or both hands to come into
contact with the saw blade.
13
Take care of your tools
–
Keep cutting tools sharp and clean in order to be
able to work better and more safely.
–
Follow the instructions for lubrication and for tool
replacement.
– Check the connection cable of the electric tool
regularly and have it replaced by a recognised
specialist when damaged.
– Check extension cables regularly and replace
them when damaged.
–
Keep the handle dry, clean and free of oil and
grease.
14 Pull the plug out of the outlet
–
Never remove loose splinters, chips or jammed
wood pieces from the running saw blade.
– During non-use of the electric tool or prior to
maintenance and when replacing tools such as
saw blades, bits, milling heads.
– When the saw blade is blocked due to abnormal
feed force during cutting, turn the machine off
and disconnect it from power supply. Remove
the work piece and ensure that the saw blade
runs free. Turn the machine on and start new
cutting operation with reduced feed force.
15
Do not leave a tool key inserted
– Before switching on, make sure that keys and
adjusting tools are removed.
16
Avoid inadvertent starting
– Make sure that the switch is switched off when
plugging the plug into an outlet.
It is also imperative to observe the accident prevention
regulations in force in your area. The same applies for
the general rules of occupational health and safety.
m
Important!
When using the equipment, a few safety precautions
must be observed to avoid injuries and damage. Please
read the complete operating instructions and safety
regulations with due care. Keep this manual in a safe
place, so that the information is available at all times.
If you give the equipment to any other person, hand
over these operating instructions and safety regulations
as well. We cannot accept any liability for damage or
accidents which arise due to a failure to follow these
instructions and the safety instructions.
The manufacturer shall not be liable for any changes
made to the machine nor for any damage resulting from
such changes.
Even when the machine is used as prescribed it is still
impossible to eliminate certain residual risk factors.
The following hazards may arise in connection with the
machine’s construction and design:
• Contact with the saw blade in the uncovered saw
zone.
• Reaching into the running saw blade (cut injuries).
• Kick-back of workpieces and parts of workpieces
• Saw blade fracturing.
• Catapulting of faulty carbide tips from the saw blade.
• Damage to hearing if essential ear-muffs are not
worn.
• Harmful emissions of wood dust when the machine is
used in closed rooms.
m
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial appli-
cations. Our warranty will be voided if the machine is
used in commercial, trade or industrial businesses or
for equivalent purposes.
Safety information
m
Attention! The following basic safety measures
must be observed when using electric tools for protec-
tion against electric shock, and the risk of injury and
fire. Read all these notices before using the electric
tool and keep the safety instructions for later refer-
ence.
Safe work
1 Keep the work area orderly
–
Disorder in the work area can lead to accidents.
2
Take environmental influences into account
– Do not expose electric tools to rain.
–
Do not use electric tools in a damp or wet envi-
ronment.
– Make sure that the work area is well-illuminated.
– Do not use electric tools where there is a risk of
fire or explosion.
3
Protect yourself from electric shock
– Avoid physical contact with earthed parts (e.g.
pipes, radiators, electric ranges, cooling units).
4
Keep children away
– Do not allow other persons to touch the equipment
or cable, keep them away from your work area.
5
Securely store unused electric tools
– Unused electric tools should be stored in a dry,
elevated or closed location out of the reach of
children.
6
Do not overload your electric tool
– They work better and more safely in the specified
output range.
23 І 36