9
GB/IE/NI
m
WARNING:
The noise emission values can vary from the
specified values during the actual use of the electric tool, de-
pending on the type and the manner in which the electric tool is
used, and in particular the type of workpiece being processed.
Implement measures to protect against noise nuisance. In do-
ing so, take into account the complete working process, includ-
ing the times when the electric tool is working without load or
switched off. Suitable measures include regular maintenance
and care of the electric tool and the insertion tools, regular
breaks as well as proper planning of the working process.
8. Before starting the equipment
• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the packaging
and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport dam-
age.
• If possible, store the packaging until the warranty period
has expired.
m
DANGER
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
• The equipment must be securely installed, i.e. bolted down
on a workbench, base frame or similar. Use the holes on the
inner side of the frame legs for this.
• All covers and safety devices have to be properly fitted be-
fore the equipment is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed before,
watch out for foreign bodies such as nails or screws, etc.
• Before you press the On/Off switch check that the saw
blade is fitted correctly. Moving parts must run smoothly.
• Before you connect the equipment to the power supply make
sure the data on the rating plate are identical to the mains
data.
• Connect the equipment to a properly installed protective
contact socket, with at least 16 A circuit breaker.
9. Assembly
m
WARNING: Danger of injury!
Improper installation of the circular table saw may result in seri-
ous injury.
Before commissioning, properly and completely install the cir-
cular table saw, including all covers and safety devices.
Never plug the mains plug into the power socket before com-
pleting the installation.
If connections are secured with a hexagonal bolt, nut, spring
washer and washer, the washer and spring washer must be
fitted under the hexagonal bolt. The spring washer always lies
directly on the (inner) hexagonal bolt or nut.
Hexagon screws must each be inserted from outside inwards,
and the connections must be secured from the inside with nuts.
During assembly nuts and screws must only be tightened until
hand-tight, so that they cannot fall out. If you tighten the nuts
and screws fully before final assembly, the circular table saw
cannot be erected in a correct and stable manner.
9.1 Assembling the frame and table width exten-
sion (fig. 4-10)
1. Turn circular table saw upside down and place on the
floor.
2. Fasten the table width extension (6) loosely onto the saw
table (1) with the hexagonal bolts (a), the washers (c), the
spring washers (d) and the nuts (e) (fig. 6).
3. The four legs (19) are screwed to the housing together
with the table supports (24) (fig. 7).
4. Fasten the table supports (24) loosely to the table width
extensions (6) with the hexagonal bolts (a), the washers
(c), the spring washers (d) and the nuts (e). Loosely tighten
the legs (19) and the table supports (24) onto the housing
of the circular table saw with the hexagonal bolts (a).
5. Now screw the four centre struts (20a, 20b) loosely onto
the legs (19). Use the coach bolts (b), the washers (c), the
spring washers (d) and the nuts (e) (fig. 8).
6. Screw on the stands (22) at the holes in the rear legs (19).
Assembly materials: 2 coach bolts (b), the washers (c),
spring washers (d) and nuts (e) respectively (fig. 9).
ATTENTION:
Both stands must be fastened to the fasten-
ing points (23) on the rear of the machine (fig. 9).
7. Align the table width extension (6) level with the saw table.
8. Now tighten all screws for the legs (19) and the table
width extension (6).
9. Now plug the rubber feet (21) onto the legs (19) (fig.
10).
10. Place the circular table saw on the machine stand (11).
9.2 Fitting the guide rail (fig. 11+12)
1. Fit the coach bolts (b) in the respective drilled holes in the
work table and the table extensions (6), by securing these
from the rear with the flange nuts (e).
2. Tighten the flange nuts (e) lightly.
3. Connect the two guide rails (15, 15a).
4. Slide the connected rails over the guide nut on the rear,
over the coach bolts (b), until they sit central to the table
surface.
9.3 Aligning the guide rail (fig. 11+12)
1. Turn the saw blade to the maximum position out of the
saw table, by turning the crank (10) clockwise until it
reaches the stop.
2. Position the parallel stop with an opened eccentric lever
(13) on the guide rails (15) on the saw table and secure
these in the 0 position by pressing the eccentric lever (13)
fully downwards.
3. Slide the connected guide rails sufficiently far to the left,
until the parallel stop reaches the right outside of the saw
blade.
4. Now tighten the flange nuts (e) firmly to fix this position.
5. Now fit the end caps (15b) on both sides of the rail.
