Scaime eNod4-B Скачать руководство пользователя

Страница: 64 / 78

SCAIME Manual : NU-eNod4B-ETH-E-236708-D.docx

Stability criterion

None, 0.25 0.5, 1, 2d

Defines a stability interval, related to scale interval.

Zero at Startup

[Yes], [No]

Enable the Automatic Zeroing at power-on

Zero Tracking

[Yes], [No]

Enable the Zero tracking function

Legal for trade
Switch

(Available depending
on version)

[Yes], [No]

Enable the legal for trade mode.

The prerequisite conditions for the activation of legal for trade mode
are:

The weight unit must be one of the following: mg, g, kg, t, ct,
µg, oz. (possibility to put spaces after unit)

The stability criterion must be 0.25 d.

Filter settling time must be less than 1 second in transmitter
mode.

The quotient (Maximum capacity / Scale interval) must be less
or equal to 6000.

On eNod4-C, zero tracking device must not be activated
together with dynamic zero tracking device.

On eNod4-T, C and D this mode has an effect on user calibration. Thus,
this mode must be activated before processing any calibration.

Save Tare in FRAM

[Yes], [No]

It allows saving tare in non-volatile memory (FRAM).

Save Zero in FRAM

[Yes], [No]

It allows saving zero in non-volatile memory (FRAM).

Audit trail (Available depending on version)

Содержание eNod4-B















































































Результаты поиска

Содержание eNod4-B

Отзывы:

Похожие инструкции для eNod4-B

Бренды по названию

Популярные бренды

Scaime eNod4-B, Руководство пользователя

Результаты поиска

Содержание eNod4-B

Отзывы:

Похожие инструкции для eNod4-B

Бренды по названию

Популярные бренды