SBC PCD1.Room Скачать руководство пользователя страница 43

Страница: 43 / 95

Hardware Manual PCD1.M2110R1 │ Document 27-619 │ Version ENG 04 │ 2018-08-20

Saia-Burgess Controls AG

Program Download and Backup

CPU / Control Process Unit

3-20

Backup to flash memory modules

For the use of “backup/restore” on the internal FLASH, a folder name PCD_

BACKUP must be created.

Backup to M1 flash

Please note that the M1

flash must be deleted

beforehand.

When using use of the

backup function to M1

modules, no other files

should be written to the

module.

M1 FLASH

PCD_BACKUP

*.sbak

PCD1 #1

PCD1 #2

Please note that a 512 kByte user program and 128 kByte RAM DB/text will

generate a file of approximately the same size.

Limitations:

Files generated cannot be copied directly from one folder to another! These files

may not be deleted from the original folder or renamed. If they are, the restore

function will no longer work correctly in this case!

The following window will

appear.

Click OK to start

the backup process.

Содержание PCD1.Room
































































































Результаты поиска

Содержание PCD1.Room

Отзывы:

Похожие инструкции для PCD1.Room

Бренды по названию

Популярные бренды

SBC PCD1.Room, Руководство по оборудованию

Результаты поиска

Содержание PCD1.Room

Отзывы:

Похожие инструкции для PCD1.Room

Бренды по названию

Популярные бренды