SBC PCD1.Room Скачать руководство пользователя страница 93

Страница: 93 / 95

Hardware Manual PCD1.M2110R1 │ Document 27-619 │ Version ENG 04 │ 2018-08-20

Saia-Burgess Controls AG

Glossary

Annex

A-4

A.3 Glossary

Backup

Datas save on media

Base address

See chapter 2.1.3 “Addressing” → “Plug-in Input

and Output Modules”

Compiler

A compiler (from the word compile, to collect)

is a program which translates the source text

(source code) of another program, which is provided

in a specific programming language, into a character

sequence that is understandable for the computer.

CPU (Central Processing Unit) Housing with central unit, the heart of the PCD
Device

Device

Download

Abb. “DnLD” Save data to PCD

Element

e.g. PLC input, PLC output, flag, register, etc.

Linker

After the compiler has done its work, the linker

combines the individual files to create a program.

LIO (Local Input Output)

Inputs/outputs on the CPU (on-board) or connected

through the I/O bus (not PCD1) on the CPU.

Media

Media refers to inputs/outputs, flags, registers, etc.

in the PCD family.

Media mapping

Assignment of digital and analogue I/O values to flags

and registers.

Modules

Carrier cards for input/output electronics

Module holder

CPU, LIO or RIO devices which can accommodate

the aforementioned modules.

Motherboard

Main circuit board (CPU)

Instruction list ( PCD program code)

New technology, means the PCD generation following

the first generation

On-board

means mounted “on the CPU circuit board”

Parsing

A parser is often a type of compiler, which checks

the correct syntax of the program.

PGU

Programmable Unit → programming unit

Port

Interface designation

Buffer battery

Retention of memory content and continuation

of the clock after a power supply shut-down.

PWM

PWM stands for Pulse Width Modulation. Pulse width

modulation works with a constant pulse rate and

a constant pulse amplitude, only the pulse width is

variable. Because the pulse rate is constant, but the

pulse width changes, the pulse duty factor changes.
With a PWM output, it is possible to output analog

values without expensive A / D converters.

Restore

Saved datas load from media

Resources

In this case inputs or outputs,

RIO (Remote Input Output)

Inputs/outputs on the CPU (on-board) or connected

through the I/O bus on the CPU.

Slot

Slot for plug-in

Содержание PCD1.Room
































































































Результаты поиска

Содержание PCD1.Room

Отзывы:

Похожие инструкции для PCD1.Room

Бренды по названию

Популярные бренды

SBC PCD1.Room, Руководство по оборудованию

Результаты поиска

Содержание PCD1.Room

Отзывы:

Похожие инструкции для PCD1.Room

Бренды по названию

Популярные бренды