Sawn Craft Zero 32 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 22

background image

Sawn Craft Zero 32 Manual

4/18/16

14

7)

Solder the wires to the motor and the ESC, shortening the wires as desired to make a clean
installation. Solder the battery connector to the ESC. Run the ESC radio connector to the receiver.
Tuck the excess wire through the hole provided to make a neat wiring installation. Secure the ESC
with a spot of glue.

8)

Attach a strip of the opposite side of Velcro™ hook and loop tape to the underside if the horizontal
fuselage component than you use on your batteries. Make it longer that the battery to allow fine
adjustment to the plane's center of gravity. Attach the opposing hook and loop tape to battery
packs to hold them in place when in use.

«
...
15
16
17
18
19
...
»

Содержание Zero 32























Отзывы:

Нет отзывов

Похожие инструкции для Zero 32

Lights & Sounds

Бренд: Learning Resources Страницы: 2

Бренд: Zhejiang Jiajia Ride-On Co. Страницы: 27

Бренд: Enabling Devices Страницы: 2

Tank Car 4-axle 67230

Бренд: BRAWA Страницы: 4

Super Heroes 6862

Бренд: LEGO Страницы: 64

Gloster Meteor F.4 interior S.A.

Бренд: Eduard Страницы: 2

Бренд: TWM Страницы: 15

3-in-1 Ride-On Firetruck

Бренд: Mega Bloks Страницы: 6

Tamagochi Friends

Бренд: Bandai Страницы: 4

Бренд: Faller Страницы: 12

B-17E/F engines

Бренд: Eduard Страницы: 2

0067 85006700200

Бренд: Monogram Страницы: 33

VISION Line 700E Hudson

Бренд: Lionel Страницы: 32

Бренд: Kavan Страницы: 16

Бренд: THUNDER TIGER Страницы: 29

Smokescreen 7051

Бренд: Hasbro Страницы: 16

Бренд: Trix Страницы: 76

Spitfire Mk.I S.A.

Бренд: Eduard Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды