Savory SP-5 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 20

Savory SP-5 Скачать руководство пользователя страница 14

SP-5 Service Manual

14

GLASS FRONT

Disassembly Instructions:
1. Disconnect main voltage.
2. Remove the pop rivets holding the washers by

drilling out their centers.

3. Remove the pop rivets holding the glass strip by

drilling.

4. Remove the silicone strip.

Assembly Instructions:
1. Install new silicone strips on both top and

bottom.

2. Install new silicone strips on the glass strips.
3. Place the glass front with the upper and lower

silicone strip in the door.

4. Push the glass front with the upper and lower

silicone strip in the door.

5. Install the glass strip.
6. Adjust the glass front to center it and then pop

rivet the glass strips in place.

7. Push the glass front toward the grill and pop

rivet the washers in place to make the glass
solidly fixed.

8. Fill the pop rivets with silicone sealant.

REQUIRED PARTS

QTY

POSITION

Glass Front

1

1

Glass Gasket

2

2

Door Gasket

2

3

1/8” Pop Rivets, Length

8

4

5/32” Pop Rivets, Length

4

5

DOOR REMOVAL

1. Disconnect main voltage.
2. Disconnect the electric connections in the

electric compartment.

3.  Remove the cover plate underneath the grill.
4.  Remove the bolt in the pivot.
5.  Tilt the door forward and lift the door upwards.

DOOR INSTALLATION

1. Make sure the (3.94”) +/- 1mm distance is kept

when you assemble.

2. Also make sure the transparent cable protection

is inserted through the pivot bushing.

3. Assemble in reverse order according to steps 1-

5 above.

NONE: Connect the earth cable.

«
...
12
13
14
15
16
...
»

Содержание SP-5





















Отзывы:

Нет отзывов