Savory SP-5 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 20

Savory SP-5 Скачать руководство пользователя страница 13

SP-5 Service Manual

13

INSULATION GROMMETS

Disassembly Instructions:
1.  Disconnect main voltage.
2.  Remove the quartz tube.
3.  Remove the electrical connections.
4.  Remove the nuts that hold the IR fixtures in place.
5.  Remove the top nut from the stud screw.
6.  Disassemble the insulation grommets.

Assembly Instructions:
1.  Assemble in reverse order according to steps 1-6 above.

NOTE: The insulation assembly should not be rigid when
assembled.

REQUIRED PARTS

QUANTITY

POSITION

Insulation Grommets

1 Set

1

DOOR GASKETS

Disassembly Instructions:
1.  Disconnect main voltage.
2.  Remove the 4 pop rivets by drilling out their centers.
3.  Remove the glass trim strip.
4. Remove

the

gasket.

Assembly Instructions:
1. Assemble in reverse order according to steps 1-4 above.

NOTE: Fill the pop rivets with silicone sealant.

REQUIRED PARTS

QTY

POSITION

Door Gasket

1

1

POWER UNIT

This figure shows how to change between degrees Celsius
(Fig 2) instead of Fahrenheit (Fig 1).

«
...
11
12
13
14
15
...
»

Содержание SP-5





















Отзывы:

Нет отзывов