Savory SP-5 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 20

Savory SP-5 Скачать руководство пользователя страница 10

SP-5 Service Manual

10

Figure 11

Figure 12

Figure 13

SLEEVE BEARING

Disassembly Instructions:
1.  Disconnect main voltage.
2.  Remove the Grill Motor.
3.  Force the journal bearing out of the bearing

mount by pressing.

Assembly Instructions:
1. Assemble in reverse order according to

steps 1-3 above.

NOTE: The joint in the sleeve bearing should not
be positioned in a vertical direction.

REQUIRED PARTS

QTY

POSITION

Sleeve Bearing

1

2

RUBBER MOUNTS

Disassembly Instructions:
1.  Disconnect main voltage.
2.  Remove the Grill Mount.
3.  Remove the rubber mount.

Assemble Instructions:
1.  Assemble in reverse according to steps 1-3

above.

NOTE: The control measurements according to
Figure 15.

REQUIRED PARTS

QTY

POSITION

Rubber Mounts

1

1

BEARING SHELF

Disassembly Instructions:
1.  Disconnect main voltage.
2.  Remove the left outer wall.
3.  Remove the bolt holding the bearing shelf.

Assembly Instructions:
1. Assemble in reverse order according to

steps 1-3 above.

NOTE: Make sure the bearing shelf is
assembled with the milled surface horizontal.
Note the control measurements according to
Figure 15.

REQUIRED PARTS

QTY

POSITION

Bearing Shelf

1

1

«
...
8
9
10
11
12
...
»

Содержание SP-5





















Отзывы:

Нет отзывов